Page tree
Skip to end of metadata
Go to start of metadata

Overview

Equipment Details


Average Installation Time


On This Page

Make: [VARIES]
Pulse Interval 400

LC: If 100 does not work try -49ms
TEST F2 Reader Installation Guides


TODO


Known Models

JTD32DG
JTD32DGECN0011
STD32DG
TEST F2 Reader Installation Guides

This document assumes the installer has working knowledge of hand tools and of the target machine in question. Physical modification of machine may be required, including modification of machine panels and internal modification to accommodate cables or harnesses. It is recommended that the instructions contained herein be performed by individuals who are qualified to perform these tasks. Card Concepts Inc. takes no responsibility for the accuracy of this document or for any damage that may occur to target machine.

Required Hardware

Card Reader

Part IDDescriptionImage
C-5401
F2 FasCard Reader

Recommended Tools and Supplies (Not Included)

See 0465 FasCard F2 Install Guide for more information.

Installation

    Page not found for multiexcerpt macro.
The page: null was not found. Please check/update the page name used in the 'multiexcerpt-include' macro.

Install Mounting Hardware

Coin and Card

P/N: C-5710
Rubber Grommet
3/4"
Qty: 1
P/N: C-6801
F2 Reader Mounting Kit
Universal
Qty: 1

  1. Place the C-6700-TEMP Drill Template on the desired mounting location.

  2. Verify included harnesses will reach desired location without encountering interference from internal machine components.

  3. Refer to FasCard Mounting Guide for further instructions.

Connect Power

P/N: C-5101
Spade Taps
18-14 AWG
Qty: 3
P/N: C-5210
Power Adapter Harness
CGI
Qty: 1
P/N: C-5500-84
Power Extension Harness
84"
Qty: 1
P/N: C-5602
Power Converter
Shine STV-12-30
Qty: 1

  1. Tap power as described in the Fascard Reader Install - Universal Concepts document using the C-5101 Spade Taps provided.
  2. Connect the C-5210 Power Adapter Harness to the installed spade taps. Connect the opposite end to the C-5602 Power Converter.
  3. Connect the C-5500-84 Power Extension Harness to the appropriate connector on the C-5602 Power Converter. The remaining cable end connects to the FasCard reader.

Connect Coin Sense Harness

Coin Drop: Factory - After Serial #DTCK9401011756

P/N: C-6250
Coin Sense Harness
can use C-6250-144
Qty: 1

  1. Disconnect the Coin Drop from the Machine Control Assembly.
  2. Connect the C-6250 Coin Sense Harness to the harness connected to the Coin Drop.

Coin Drop: Factory - Before Serial #DTCK9401011756

P/N: C-6253
Coin Sense Harness
28"
Qty: 1

  1. Disconnect the Coin Drop from the Machine Control Assembly.
  2. Connect the C-6253 Coin Sense Harness to the harness connected to the Coin Drop.

Connect Machine Interface Harness

Pulse - After Serial #DTCK9401011756

P/N: C-5300-NC
Machine Start Harness
can use C-5300-NC-144
Qty: 1

  1. Connect the C-5300-NC Machine Start Harness to the Coin 1 harness on the Machine Control Assembly.

Pulse - Before Serial #DTCK9401011756

P/N: C-5305
Machine Start Harness
40" - Male taps, Rq. Female
Qty: 1

  1. Connect the C-5305 Machine Start Harness to the Coin 1 harness on the Machine Control Assembly.

Optional: Stack Add-on Installation

Pulse - After Serial #DTCK9401011756

P/N: C-5300-NC-144
Machine Start Harness
144" Alliance
Qty: 1
P/N: C-6250-144
Coin Sense Harness
144" length
Qty: 1
P/N: C-6400
F2, Stack Add On Board - SLV
Pulse / SingleVend
Qty: 1

  1. Run C-5300-NC-144 Machine Start Harness and C-6250-144 Coin Sense Harness to the second Machine Control Assembly.
  2. Connect C-5300-NC-144 Machine Start Harness to the Coin 1 connection and the C-6250-144 Coin Sense Harness to the Coin Drop on the second Machine Control Assembly.
  3. Connect the C-6400 Stack Add-on Board to port 5 (Serial Connection Port) on the F2 reader.
    1. Connect the Machine Start Harness connected to the upper pocket Machine Control Assembly to Port 2 on the FasCard Reader.
    2. Connect the Machine Start Harness connected to the lower pocket Machine Control Assembly to Stack Add-on Board.
  4. Connect the Coin Sense Harness connected to the upper pocket Coin Drop to port 3 (Coin 1 Sense Harness Connection Port) on the F2 reader.
  5. Connect the Coin Sense Harness connected to the lower pocket Coin Drop to port 4 (Coin 2 Sense Harness Connection Port) on the F2 reader.

Pulse - Before Serial #DTCK9401011756

P/N: C-5305-120
Machine Start Harness
120" - Male taps, Rq. Female
Qty: 1
P/N: C-6253-120
Coin Sense Harness
120"
Qty: 1
P/N: C-6400
F2, Stack Add On Board - SLV
Pulse / SingleVend
Qty: 1

  1. Run C-5305-144 Machine Start Harness and C-6253-120 Coin Sense Harness to the second Machine Control Assembly.
  2. Connect C-5305-144 Machine Start Harness to the Coin 1 connection and the C-6253-120 Coin Sense Harness to the Coin Drop on the second Machine Control Assembly.
  3. Connect the C-6400 Stack Add-on Board to port 5 (Serial Connection Port) on the F2 reader.
    1. Connect the Machine Start Harness connected to the upper pocket Machine Control Assembly to Port 2 (Pulse Connection Port) on the FasCard Reader.
    2. Connect the Machine Start Harness connected to the lower pocket Machine Control Assembly to Stack Add-on Board.
  4. Connect the Coin Sense Harness connected to the upper pocket Coin Drop to port 3 (Coin 1 Sense Harness Connection Port) on the F2 reader.
  5. Connect the Coin Sense Harness connected to the lower pocket Coin Drop to port 4 (Coin 2 Sense Harness Connection Port) on the F2 reader.

Connect and Mount Reader

    Page not found for multiexcerpt macro.
The page: null was not found. Please check/update the page name used in the 'multiexcerpt-include' macro.

  1. Feed remaining harness ends through the mounting hole as described in the F1: FasCard Reader Mounting Guide.
  2. Connect the free end of the Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.
  3. Connect the free end of the Coin Sense Harness to port 3 (Coin Sense Harness Connection Port) as shown in the image above.
  4. Connect the free end of the C-5500-84 Power Harness to port 1.
  5. Secure the FasCard reader to base as described in the FasCard Mounting Guide.

Machine Configuration

TODO

FasCard Admin Site Configuration

Use the following settings depending on the Machine Start Harness used.

Pulse (C-5300-NC) - After Serial #DTCK9401011756

  1. Equipment Type: SingleVend
  2. Pulse Length: -80

Pulse (C-5305) - Before Serial #DTCK9401011756

  1. Equipment Type: SingleVend
  2. Pulse Length: 100

    Page not found for multiexcerpt macro.
The page: null was not found. Please check/update the page name used in the 'multiexcerpt-include' macro.