Page tree
Skip to end of metadata
Go to start of metadata

Overview

Equipment Details


Average Installation Time


On This Page

Make: [VARIES]
W: Alliance ACA Front-Load Washer - MDC II
D: Alliance MDC II Small Dryer
TEST F2 Reader Installation Guides


TODO


Known Models

HTEBCASP175TW01
HTEBYASP285CW01
HTGBCASP115TW01
HTGBYASP115TW01
TEST F2 Reader Installation Guides

This document assumes the installer has working knowledge of hand tools and of the target machine in question. Physical modification of machine may be required, including modification of machine panels and internal modification to accommodate cables or harnesses. It is recommended that the instructions contained herein be performed by individuals who are qualified to perform these tasks. Card Concepts Inc. takes no responsibility for the accuracy of this document or for any damage that may occur to target machine.

Required Hardware

Card Reader

Part IDDescriptionImage
C-5401
F2 FasCard Reader

Recommended Tools and Supplies (Not Included)

See 3251 FasCard F2 Install Guide for more information.

Installation

    Page not found for multiexcerpt macro.
The page: null was not found. Please check/update the page name used in the 'multiexcerpt-include' macro.

Install Mounting Hardware

Coin and Card

P/N: C-6801
F2 Reader Mounting Kit
Universal
Qty: 1

  1. Place the C-6700-TEMP Drill Template on the desired mounting location.

  2. Verify included harnesses will reach desired location without encountering interference from internal machine components.

  3. Refer to FasCard Mounting Guide for further instructions.

Card Only

P/N: C-6801
F2 Reader Mounting Kit
Universal
Qty: 1

  1. Place the C-6700-TEMP Drill Template on the desired mounting location.

  2. Verify included harnesses will reach desired location without encountering interference from internal machine components.

  3. Refer to FasCard Mounting Guide for further instructions.

Connect Power

P/N: C-6204
Power Adapter Harness
F2 12vDC Power Harness
Qty: 1

  1. Connect the C-6204 12VDC Power Harness to the H10 Connection on the Machine Control Assembly.
  2. Connect the green wire to a chassis ground.
  3. The remaining end (3-pin molex) connects directly to the rear of the F2 FasCard Reader.

Connect Coin Sense Harness

Coin Drop: Factory

P/N: C-6250
Coin Sense Harness
can use C-6250-144
Qty: 1

  1. Disconnect the Coin Drop from the Machine Control Assembly.
  2. Connect the C-6250 Coin Sense Harness to the harness connected to the Coin Drop.

Connect Machine Interface Harness

Pulse

P/N: C-5300-NC
Machine Start Harness
can use C-5300-NC-144
Qty: 1

  1. Connect the C-5300-NC Machine Start Harness to the Coin 1 connector on the Machine Control Assembly.

Serial

P/N: C-5240
Machine Start Harness
can use C-5240-144
Qty: 1

  1. Connect the C-5240 Machine Start Harness to the H3 connector on the Machine Control Assembly.

Connect and Mount Reader

    Page not found for multiexcerpt macro.
The page: null was not found. Please check/update the page name used in the 'multiexcerpt-include' macro.

  1. Feed remaining harness ends through the mounting hole as described in the F1: FasCard Reader Mounting Guide.
  2. Connect the free end of the Machine Start Harness:
    1. If following steps for a serial Machine Start Harness to port 5 (Serial Connection Port) as shown in the image above.
    2. If following steps for a pulse Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.
  3. Connect the free end of the C-6250 Coin Sense Harness to port 3 (Coin Sense Harness Connection Port) as shown in the image above.
  4. Connect the free end of the C-6204 Power Harness to port 1.
  5. Secure the FasCard reader to base as described in the FasCard Mounting Guide.

Machine Configuration

ACA machines using a serial configuration require dip switch 3 on the Machine Control Board to be set to the 'ON' position. Leave all other dip switches as is.

FasCard Admin Site Configuration

Use the following settings depending on the Machine Start Harness used.

Washer

Pulse (C-5300-NC)

  1. Equipment Type: SingleVend
  2. Pulse Length: 80

Serial (C-5240)

  1. Equipment Type: Alliance ACA H7S Front Load Washer A1 - MDC II

Dryer

Pulse (C-5300-NC)

  1. Equipment Type: SingleVend
  2. Pulse Length: 80

Serial (C-5240)

  1. Equipment Type: Alliance ACA H7S Small Dryer A1 - MDC II

    Page not found for multiexcerpt macro.
The page: null was not found. Please check/update the page name used in the 'multiexcerpt-include' macro.