Page tree
Skip to end of metadata
Go to start of metadata
Manufacturers
Purpose

CCI supports serial (two-way) communication with many different equipment manufacturer controls. This opens up the following possibilities from the CCI interface (when supported by the control):

  • Multi-level pricing: Different vend prices for different cycles (i.e. Hot/Warm/Cold) and modifiers (i.e. Extra Rinse/Extra Wash)
  • Machine Programming: Change machine settings (i.e. cycle times, water levels, temperatures, etc)

 If a control is not listed or marked as not supported, it can still be started by the CCI card system using a standard relay pulse.

Alliance (Huebsch, IPSO, Primus, Speed Queen)

Machine ControlEquipment Type
Notes
A-MicroWasher Extractor(tick)

Requires special daughter board and micro chip available only from Alliance Laundry Systems.

Machine options cannot be configured through CCI interface.

B-Micro-(error)Control does not support serial interface.
Galaxy 200 (Centurion)-(error)Control does not support serial interface.
Galaxy 400 (Centurion)-(error)Control does not support serial interface.
Galaxy 600 (Centurion)Washer Extractor
Tumbler Dryer
(tick)
Galaxy 600 (ACA)Front-Load Washer(tick)Not supported in LaundryCard v6.
Maestro VWasher Extractor(tick)
Micro-Display (MDC)Front-Load Washer
Top-Load Washer
Small Dryer
Tumbler Dryer 
(tick)
MDC II (ACA)Front-Load Washer
Small Dryer 
(tick)Not supported in LaundryCard v6.
NetMaster-(error)Control does not support serial interface.
Quantum Standard (Centurion)-(error)Control does not support serial interface.
Quantum Silver (Centurion)Washer Extractor(tick)
Quantum Gold (Centurion)

Washer Extractor
Front-Load Washer
Top-Load Washer
Tumbler Dryer
Small Dryer 

(tick)
Quantum+ (ACA)Front-Load Washer
Top-Load Washer 
(tick)Not supported in LaundryCard v6
XControl-(error)CCI does not support serial integration.
XControl+-(error)CCI does not support serial integration.

Continental

Machine ControlEquipment Type
Notes
Coin ControlWasher Extractor(tick)

Requires Continental serial daughterboard.

v39/v72 machine firmware recommended.

ProfitPlusWasher Extractor(tick)

Requires Continental serial daughterboard.

v39/v72 machine firmware recommended.

Dexter

Machine ControlEquipment Type
Notes
A-Series (1.0)-(error)Control does not support serial interface.
C-Series (1.5)Washer Extractor(tick)

Not supported in LaundryCard v6

Tested against machine firmware level 1.4

Laundrylux (Wascomat / Electrolux)

LaundryCard: Re-ordering or adding/disabling cycles is not supported. The default cycles and order must be used.

When connected serially the possibility to make a pause is blocked. Also within the regret time. It is in this case not even possible to activate the pause function by the service program. The configuration setting for pause function (Config 1) will not affect the function of the machine.

Machine ControlEquipment Type
Notes
EmeraldWasher(error)CCI does not support serial interface.
Compass (Gen 6)Washer(tick)6.50 machine firmware recommended.
Compass Pro (Gen 7)Washer(tick)

8.06 machine firmware recommended.

Not supported in LaundryCard v6.

Pronto Washer/DryerCombo Washer/Dryer(tick)Not supported in LaundryCard v6
CrossOverWasher(tick)Not supported in LaundryCard v6

LG

Machine ControlEquipment Type
Notes
Giant-CWasher
Dryer (FasCard Only) 
(tick)Not supported in LaundryCard v6.
Giant-C PlusWasher
Dryer (FasCard Only) 
(tick)Not supported in LaundryCard v6.
TitanWasher
Dryer (FasCard Only)
 (tick)Not supported in LaundryCard v6. 

Maytag / Whirlpool

Machine ControlEquipment Type
Notes
Gen 1Washer
Dryer
(tick)Super Cycle supported on certain machines. Deluxe Cycle, Ultimate Cycle and Cycle Based Pricing are NOT supported.
Gen 2-(error)Not supported by CCI.

Vending

Machine ControlEquipment Type
Notes
MDB Level 1ANY(tick)Pricing is set on the vending machine.
MDB Level 2-(error)Not supported by CCI.
MDB Level 3-(error)Not supported by CCI.