Page tree
Skip to end of metadata
Go to start of metadata

Overview

Equipment Details


Average Installation Time


On This Page

Make: Wascomat
TEST F2 Reader Installation Guides


TODO


Known Models

SU620CC
SU630CC
SU640CC
SU655CC
SU675CC
TEST F2 Reader Installation Guides

This document assumes the installer has working knowledge of hand tools and of the target machine in question. Physical modification of machine may be required, including modification of machine panels and internal modification to accommodate cables or harnesses. It is recommended that the instructions contained herein be performed by individuals who are qualified to perform these tasks. Card Concepts Inc. takes no responsibility for the accuracy of this document or for any damage that may occur to target machine.

Required Hardware

Card Reader

One of the following readers.

Part IDDescriptionImage
C-3001
LC WiFi Reader
Front/Vertical Mount
C-3002
LC WiFi Reader
Top/Horizontal Mount
C-5401
F2 FasCard Reader
Front Mount
C-5402
F2 FasCard Reader
High Front/Top Mount
C-5403
FLEX Reader
Front/Vertical Mount
C-5404
FLEX Reader
Top/Horizontal Mount

Recommended Tools and Supplies (Not Included)

See 0384 F2 Reader Install Guide for more information.

Installation

    Page not found for multiexcerpt macro.
The page: null was not found. Please check/update the page name used in the 'multiexcerpt-include' macro.

Install Mounting Hardware

Coin and Card

P/N: C-6801
F2 Reader Mounting Kit
Universal
Qty: 1

  1. Place the C-6700-TEMP Drill Template on the desired mounting location.

  2. Verify included harnesses will reach desired location without encountering interference from internal machine components.

  3. Refer to FasCard Mounting Guide for further instructions.

Card Only - 30lb and Smaller Models

P/N: C-1059
Nut
10-32 - Kep
Qty: 2
P/N: C-6801
F2 Reader Mounting Kit
Universal
Qty: 1
P/N: C-6922
Mounting Bracket
6" Angled
Qty: 1

  1. Remove existing coin box and coin drop.

  2. Attach the C-5414 Standard Mounting Bracket to the C-6922 Mounting Bracket using the C-5702 Chase Nipple and C-5703 Nut.
  3. Install the C-6922 Mounting Bracket into the coin vault opening. Secure in place using the C-1059 Kep Nuts.

Card Only - 40lb and Larger Models

P/N: C-1059
Nut
10-32 - Kep
Qty: 2
P/N: C-6801
F2 Reader Mounting Kit
Universal
Qty: 1
P/N: C-6920R1
Mounting Bracket
6" Straight w/ studs
Qty: 1

  1. Remove existing coin box and coin drop.

  2. Attach the C-5414 Standard Mounting Bracket to the C-6920R1 Mounting Bracket using the C-5702 Chase Nipple and C-5703 Nut.
  3. Install the C-6920R1 Mounting Bracket into the coin vault opening. Secure in place using the C-1059 Kep Nuts.

Connect Power

P/N: C-5101
Spade Taps
18-14 AWG
Qty: 3
P/N: C-5210
Power Adapter Harness
CGI
Qty: 1
P/N: C-5500
Power Extension Harness
25.5"
Qty: 1
P/N: C-5602R1
Power Converter
SMT-012-018VW
Qty: 1

  1. Tap power as described in the Fascard Reader Install - Universal Concepts document using the C-5101 Spade Taps provided.
  2. Connect the C-5210 Power Adapter Harness to the installed spade taps.
  3. Connect the C-5210 Power Adapter Harness to the C-5602 Power Converter.
  4. Connect the C-5500 Power Extension Harness to the appropriate connector on the C-5602 Power Converter. The remaining cable end connects to the FasCard reader.
  5. Connect the opposite end of the C-5210  Power Adapter Harness to the C-5602 Power Converter.
  6. Connect the C-5500 Power Extension Harness to the appropriate connector on the C-5602 Power Converter. The remaining cable end connects to the FasCard reader.

Connect Coin Sense Harness

Coin Drop: Factory

P/N: C-6357
Coin Sense Harness (SA)
can use C-6357-144
Qty: 1

  1. Disconnect the Coin Drop from the Machine Control Assembly.
  2. Connect the C-6357 Coin Sense Harness to the harness connected to the Coin Drop.

Connect Machine Interface Harness

Pulse

P/N: C-5353R1
Machine Start Harness (SA)
40" - LaundryLux
Qty: 1

  1. Connect the C-5353R1 Machine Start Harness to the Coin 1 connection on the Machine Control Assembly.

Serial

P/N: C-0126-MLV
Machine Start Harness (SA)
Wascomat Compass
Qty: 1
P/N: C-5359
Machine Start Harness (SA)
Compass
Qty: 1

  1. Connect the C-5359 Machine Start Harness to the Input connection on the Machine Control Assembly.
  2. Connect the C-0126-MLV Machine Start Harness to the RS232 connection on the Machine Control Assembly.

Connect and Mount Reader

Item No.ComponentNotes
1Power Connection PortUtilizes the same power harnesses as the first generation FasCard reader.
2Pulse Connection PortConnection point for pulse machine start harnesses.
3Coin 1 Connection PortThis is the connection point for the harness input associated with Coin 1.
4Coin 2 Connection PortThis is the connection point for the harness input associated with Coin 2.
5Serial Connection PortThis is the connection point for serial machine start harnesses.

  1. Feed remaining harness ends through the mounting hole as described in the FasCard Mounting Guide.
  2. For Serial Setups:
    1. Connect the free end of the C-5359 Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.
    2. Connect the free end of the C-0126-MLV Machine Start Harness to port 5 (Serial Connection Port) as shown in the image above.
  3. For Pulse Setups:
    1. Connect the free end of the C-5353R1 Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.
  4. Connect the free end of the C-6357 Coin Sense Harness to port 3 (Coin Sense Harness Connection Port) as shown in the image above.
  5. Connect the free end of the C-5500 Power Harness to port 1.
  6. Secure the FasCard reader to base as described in the FasCard Mounting Guide.

Machine Configuration

TODO

FasCard Admin Site Configuration

Use the following settings depending on the Machine Start Harness used.

Pulse (C-5353R1)

  1. Equipment Type: SingleVend
  2. Pulse Length: 500

Serial (C-0126-MLV)

  1. Equipment Type: Laundrylux Compass Washer