Page tree
Skip to end of metadata
Go to start of metadata

Overview

Equipment Details


Average Installation Time


On This Page

Make: ADC
TEST F2 Reader Installation Guides


TODO


Known Models

EWH60M2
EWH30
EWH40
EWH40MC2
EWH40MR
EWH40MR
EWH40MR
EWH40MRC2
EWH60
EWH60M2
EWH60M2
EWH60M2
EWH60M2
EWH60M2
EWH60M2
EWH60M2
EWH60M2
EWH60M2
EWH60M2
EWH60M2
EWR25
EWR40
EWR60
EWR60MR
EWS40M2
EWS40MC
EWS40MC
EWS40MC
EWS40MC2
EWS60M2
EWS60MC
EWS60MC
EWS60MC
EWS60MC
EWS60MC2
EWS60MR
EWS60MR
EWS80M2
EWS80MC1
EWS80MC2
EWS80MC2
EWS80MC2
EWS80MR
EWS80MR1
TEST F2 Reader Installation Guides

This document assumes the installer has working knowledge of hand tools and of the target machine in question. Physical modification of machine may be required, including modification of machine panels and internal modification to accommodate cables or harnesses. It is recommended that the instructions contained herein be performed by individuals who are qualified to perform these tasks. Card Concepts Inc. takes no responsibility for the accuracy of this document or for any damage that may occur to target machine.

Required Hardware

Card Reader

One of the following readers.

Part IDDescriptionImage
C-3001
LC WiFi Reader
Front/Vertical Mount
C-3002
LC WiFi Reader
Top/Horizontal Mount
C-5401
F2 FasCard Reader
Front Mount
C-5402
F2 FasCard Reader
High Front/Top Mount
C-5403
FLEX Reader
Front/Vertical Mount
C-5404
FLEX Reader
Top/Horizontal Mount

Recommended Tools and Supplies (Not Included)

See 0456 F2 Reader Install Guide for more information.

Installation

    Page not found for multiexcerpt macro.
The page: null was not found. Please check/update the page name used in the 'multiexcerpt-include' macro.

Install Mounting Hardware

Coin and Card

P/N: C-6801
F2 Reader Mounting Kit
Universal
Qty: 1

  1. Place the C-6700-TEMP Drill Template on the desired mounting location.

  2. Verify included harnesses will reach desired location without encountering interference from internal machine components.

  3. Refer to FasCard Mounting Guide for further instructions.

Connect Power

P/N: C-5101
Spade Taps
18-14 AWG
Qty: 2
P/N: C-5336
Power Adapter Harness
Dexter Stack
Qty: 1
P/N: C-5500
Power Extension Harness
25.5"
Qty: 1
P/N: C-5602R1
Power Converter
SMT-012-018VW
Qty: 1

  1. Tap power as described in the Fascard Reader Install - Universal Concepts document using the C-5101 Spade Taps provided.
  2. Connect the C-5336 Power Adapter Harness to the installed spade taps- Blue to Black and Brown to Red. Secure the green ground terminal under the bolt on top of the washer drum.
  3. Connect the opposite end of the C-5336 Power Adapter Harness to the C-5602 Power Converter.
  4. Connect the C-5500 Power Extension Harness to the appropriate connector on the C-5602 Power Converter. The remaining cable end connects to the FasCard reader.

Connect Coin Sense Harness

Coin Drop: Factory

P/N: C-6342
ADC Coin Sense Harness
F2
Qty: 1

  1. Disconnect the coin drop harness from the terminal stripby disconnecting the Yellow and Brown wires.
    1. If the coin drop is not connected to a terminal strip you will need to cut the wires and connect the coin drop ends of the wires to the coin sense harness.
  2. Connect the C-6342 Coin Sense Harness to the terminal strip, Brown to Brown and Yellow to Yellow.

Connect Machine Interface Harness

Pulse

P/N: C-5341
Machine Start Harness
ADC
Qty: 1

  1. Connect the C-5341 Machine Start Harness to the terminal strip in the same position that was previously connected to the coin drop.
    1. Wire orientation is not relevant.

Connect and Mount Reader

Item No.ComponentNotes
1Power Connection PortUtilizes the same power harnesses as the first generation FasCard reader.
2Pulse Connection PortConnection point for pulse machine start harnesses.
3Coin 1 Connection PortThis is the connection point for the harness input associated with Coin 1.
4Coin 2 Connection PortThis is the connection point for the harness input associated with Coin 2.
5Serial Connection PortThis is the connection point for serial machine start harnesses.

  1. Feed remaining harness ends through the mounting hole as described in the F1: FasCard Reader Mounting Guide.
  2. Connect the free end of the C-5341 Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.
  3. Connect the free end of the C-5342 Coin Sense Harness to port 3 (Coin Sense Harness Connection Port) as shown in the image above.
  4. Connect the free end of the C-5500 Power Harness to port 1.
  5. Secure the FasCard reader to base as described in the FasCard Mounting Guide.

Machine Configuration

TODO

FasCard Admin Site Configuration

Use the following settings depending on the Machine Start Harness used.

Pulse (C-5341)

  1. Equipment Type: SingleVend
  2. Pulse Length: 100