Page tree
Skip to end of metadata
Go to start of metadata

Overview

Equipment Details


Average Installation Time


On This Page

Make: Dexter
TEST F2 Reader Installation Guides


TODO


Known Models

DDAD 30 KCS 65 EC
DDAD30KC
DDAD30KC65
DDAD30KCA
DDAD30KCA65
DDAD30KCB65
DDAD30KCB65CN
DDAD30KCB65CNTS
DDAD30KCB65US
DDAD30KCB65US
DDAD30KCB65US
DDAD30KCB65US
DDAD30KCB65US
DDAD30KCB65US
DDAD30KCS
DDAD30KCS 65EC
DDAD30KCS65
DDAD30KCS65
DDAD30KCS65
DDAD30KCS65
DDAD30KCS65
DDAD30KCS65
DDAD30KCS65
DDAD30KCS65
DDAD30KCS65
DDAD30KCS65
DDAD30KCS65
DDAD30KCS65
DDAD30KCS65
DDAD30KCS65CN
DDAD30KCS65CN.
DDAD30KCS65EC
DDAD30KCS65EC
DDAD30KCS65EC
DDAD30KCS65EC
DDAD30KCS65EC
DDAD30KCS65EC
DDAD30KCS65TS
DDAD30KCS65US
DDAD30KCS65US
DDAD30KCS65USTS
DDAD30KCW
DDAD30KCW65
DDAD30KCW65
DDAD30KCW65
DDAD30KCW65CN
DDAD30KCW65CN
DDAD30KCW65CP
DDAD30KCW65CP
DDAD30KCW65EC
DDAD30KCX65US
DDAD30KCY65CN
DDAD30KCZ65US
DDAD50KCA65
DDAD50KCA65
DDAD50KCA65
DDAD50KCA65EC
DDAD50KCA65EC
DDAD50KCS
DDAD50KCS65
DDAD50KCS65
DDAD50KCS65
DDAD50KCS6SUS
DDAD50KCW65CN
DDAG30KCS65
DDAG30KCS65
DDAG30KCS65
DDAG30KCS65
DDAG30KCW65
DDTD 30 KCS 10 EC
DDTD30KCS
DDTD30KCS10EC
DDTD30KCS10EC
DDTD30KCS10ECTS
TEST F2 Reader Installation Guides

This document assumes the installer has working knowledge of hand tools and of the target machine in question. Physical modification of machine may be required, including modification of machine panels and internal modification to accommodate cables or harnesses. It is recommended that the instructions contained herein be performed by individuals who are qualified to perform these tasks. Card Concepts Inc. takes no responsibility for the accuracy of this document or for any damage that may occur to target machine.

Required Hardware

Card Reader

One of the following readers.

Part IDDescriptionImage
C-3001
LC WiFi Reader
Front/Vertical Mount
C-3002
LC WiFi Reader
Top/Horizontal Mount
C-5401
F2 FasCard Reader
Front Mount
C-5402
F2 FasCard Reader
High Front/Top Mount
C-5403
FLEX Reader
Front/Vertical Mount
C-5404
FLEX Reader
Top/Horizontal Mount

Recommended Tools and Supplies (Not Included)

See 0578 F2 Reader Install Guide for more information.

Installation

    Page not found for multiexcerpt macro.
The page: null was not found. Please check/update the page name used in the 'multiexcerpt-include' macro.

Install Mounting Hardware

Coin and Card

P/N: C-5710
Rubber Grommet
3/4"
Qty: 1
P/N: C-6801
F2 Reader Mounting Kit
Universal
Qty: 1

  1. Place the C-6700-TEMP Drill Template on the desired mounting location.

  2. Verify included harnesses will reach desired location without encountering interference from internal machine components.

  3. Refer to FasCard Mounting Guide for further instructions.

Card Only

P/N: C-0144
Screw
8-32 x 2" - Flat
Qty: 2
P/N: C-0905
Drop Cover
2-3/8" x 4-5/8"
Qty: 1
P/N: C-5710
Rubber Grommet
3/4"
Qty: 1
P/N: C-6801
F2 Reader Mounting Kit
Universal
Qty: 1
P/N: C-6936
F2, Sm Vault Mount Bracket
Qty: 1

  1. Feed the harness ends through the coin vault opening and then through the circular opening in the C-6936 Vault Mount Bracket.
  2. Spread the C-6936 Vault Mount Bracket wings outward and then insert the C-6936 Vault Mount Bracket into the coin vault.
  3. Feed the harness ends through the C-5414 F2 Mounting Bracket.
  4. Secure the C-5414 F2 Mounting Bracket to the C-6936 Vault Mount Bracket with the C-0144 Screws.
  5. Install the C-5710 Rubber Grommet into the circular opening of the C-5414 F2 Mounting Bracket.
  6. Remove any existing coin drop.
  7. Mount the C-0905 Drop Cover using existing mounting hardware where the coin drop was previously installed.

Connect Power

P/N: C-5213
Power Adapter Harness
DDAD - AC
Qty: 1
P/N: C-5500-115
Power Extension Harness
115"
Qty: 1
P/N: C-5602R1
Power Converter
SMT-012-018VW
Qty: 1

  1. Tap power as described in the Fascard Reader Install - Universal Concepts document by connecting the C-5213 Power Adapter Harness to the power distribution panel inside the machine.

    1. 120vac: Connect the brown and blue wires to connector #2 closest to outside of machine and #4 on terminal side closest to circuit board.

    2. 240vac: Connect the brown and blue wires to connectors 3 and 5 on the terminal side closest to the circuit board.

    3. Secure the green wire beneath the ground screw.

  2. Connect the opposite end of the C-5213  Power Adapter Harness to the C-5602 Power Converter.

  3. Connect the C-5500-115 Power Extension Harness to the appropriate connector on the C-5602 Power Converter. The remaining cable end connects to the FasCard reader.

Connect Coin Sense Harness

Coin Drop: Micro Switch

P/N: C-6253
Coin Sense Harness
28"
Qty: 1

  1. Disconnect the Coin Drop from the Machine Control Assembly.
  2. Connect the C-6253 Coin Sense Harness to the harness connected to the Coin Drop.

Coin Drop: Aftermarket Imonex

P/N: C-6382
Coin Sense Harness
Imonex EM100/EM3
Qty: 1

  1. Disconnect the Coin Drop from the Machine Control Assembly.
  2. Connect the C-6382 Coin Sense Harness to the harness connected to the Coin Drop.

Coin Drop: Factory

P/N: C-6253
Coin Sense Harness
28"
Qty: 1

  1. Disconnect the Coin Drop from the Machine Control Assembly.
  2. Connect the C-6258 Coin Sense Harness to the harness connected to the Coin Drop.

Connect Machine Interface Harness

Pulse - Optical

P/N: C-5254
Machine Start Harness
Dexter Stack Dryer
Qty: 1

  1. Connect the C-5254 Machine Start Harness to the P3 connector on the Machine Control Assembly.

Pulse - Micro Switch

P/N: C-5256
Machine Start Harns (pulse)
20" - Male taps, Rq. Female
Qty: 1

  1. Connect the C-5256 Machine Start Harness to the harness previously connected to the coin drop micro switch.

Connect and Mount Reader

Item No.ComponentNotes
1Power Connection PortUtilizes the same power harnesses as the first generation FasCard reader.
2Pulse Connection PortConnection point for pulse machine start harnesses.
3Coin 1 Connection PortThis is the connection point for the harness input associated with Coin 1.
4Coin 2 Connection PortThis is the connection point for the harness input associated with Coin 2.
5Serial Connection PortThis is the connection point for serial machine start harnesses.

  1. Feed remaining harness ends through the mounting hole as described in the F1: FasCard Reader Mounting Guide.
  2. Connect the free end of the Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.
  3. Connect the free end of the Coin Sense Harness to port 3 (Coin Sense Harness Connection Port) as shown in the image above.
  4. Connect the free end of the C-5500-115 Power Harness to port 1.
  5. Secure the FasCard reader to base as described in the FasCard Mounting Guide.

Machine Configuration

TODO

FasCard Admin Site Configuration

Use the following settings depending on the Machine Start Harness used.

Pulse (C-5254 & C-5256)

  1. Equipment Type: SingleVend
  2. Pulse Length: 55