Page tree
Skip to end of metadata
Go to start of metadata


Equipment Details

Average Installation Time

On This Page

Make: Dexter
TEST F2 Reader Installation Guides


Known Models

TEST F2 Reader Installation Guides

This document assumes the installer has working knowledge of hand tools and of the target machine in question. Physical modification of machine may be required, including modification of machine panels and internal modification to accommodate cables or harnesses. It is recommended that the instructions contained herein be performed by individuals who are qualified to perform these tasks. Card Concepts Inc. takes no responsibility for the accuracy of this document or for any damage that may occur to target machine.

Required Hardware

Card Reader

One of the following readers.

Part IDDescriptionImage
LC WiFi Reader
Front/Vertical Mount
LC WiFi Reader
Top/Horizontal Mount
F2 FasCard Reader
Front Mount
F2 FasCard Reader
High Front/Top Mount
FLEX Reader
Front/Vertical Mount
FLEX Reader
Top/Horizontal Mount

Recommended Tools and Supplies (Not Included)

See 0586 F2 Reader Install Guide for more information.


    Page not found for multiexcerpt macro.
The page: null was not found. Please check/update the page name used in the 'multiexcerpt-include' macro.

Install Mounting Hardware

Coin and Card

P/N: C-5710
Rubber Grommet
Qty: 1
P/N: C-6801
F2 Reader Mounting Kit
Qty: 1

  1. Place the C-6700-TEMP Drill Template on the desired mounting location.

  2. Verify included harnesses will reach desired location without encountering interference from internal machine components.

  3. Refer to FasCard Mounting Guide for further instructions.

Card Only

P/N: C-0144
8-32 x 2" - Flat
Qty: 2
P/N: C-0905
Drop Cover
2-3/8" x 4-5/8"
Qty: 1
P/N: C-5710
Rubber Grommet
Qty: 1
P/N: C-6801
F2 Reader Mounting Kit
Qty: 1
P/N: C-6936
F2, Sm Vault Mount Bracket
Qty: 1

  1. Install the C-5710 Rubber Grommet into the circular opening of the C-5414 F2 Mounting Bracket.
  2. Feed the harness ends through the coin vault opening and then through the circular opening in the C-6936 Vault Mount Bracket.
  3. Spread the C-6936 Vault Mount Bracket wings outward and then insert the C-6936 Vault Mount Bracket into the coin vault.
  4. Feed the harness ends through the C-5414 F2 Mounting Bracket.
  5. Secure the C-5414 F2 Mounting Bracket to the C-6939 Vault Mount Bracket with the C-0144 Screws.
  6. Remove any existing coin drop.
  7. Mount the C-0905 Drop Cover using existing mounting hardware where the coin drop was previously installed.

Connect Power

P/N: C-5211
Power Adapter Harness
Qty: 1
P/N: C-5500-60
Power Extension Harness
Qty: 1
P/N: C-5602R1
Power Converter
Qty: 1

  1. Tap power as described in the Fascard Reader Install - Universal Concepts document by connecting the C-5211 Power Adapter Harness to the male spade connectors on the machine power panel.
    1. Connect the green wire to the ground terminal.
    2. A corner of the power panel cover may need to be bent slightly to allow the power harness egress.
  2. Connect the opposite end of the C-5211 Power Adapter Harness to the C-5602 Power Converter.
  3. Connect the C-5500-60 Power Extension Harness to the appropriate connector on the C-5602 Power Converter. The remaining cable end connects to the FasCard reader.

Connect Coin Sense Harness

Coin Drop: Factory

P/N: C-6253
Coin Sense Harness
Qty: 1

  1. Disconnect the Coin Drop from the Machine Control Assembly.
  2. Connect the C-6253 Coin Sense Harness to the harness connected to the Coin Drop.

Connect Machine Interface Harness


P/N: C-5256
Machine Start Harns (pulse)
20" - Male taps, Rq. Female
Qty: 1

  1. Connect the C-5256 Machine Start Harness to the Coin Drop Harness previously connected to the coin drop.

Connect and Mount Reader

Item No.ComponentNotes
1Power Connection PortUtilizes the same power harnesses as the first generation FasCard reader.
2Pulse Connection PortConnection point for pulse machine start harnesses.
3Coin 1 Connection PortThis is the connection point for the harness input associated with Coin 1.
4Coin 2 Connection PortThis is the connection point for the harness input associated with Coin 2.
5Serial Connection PortThis is the connection point for serial machine start harnesses.

  1. Feed remaining harness ends through the mounting hole as described in the F1: FasCard Reader Mounting Guide.
  2. Connect the free end of the C-5256 Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.
  3. Connect the free end of the C-6253 Coin Sense Harness to port 3 (Coin Sense Harness Connection Port) as shown in the image above.
  4. Connect the free end of the C-5500-60 Power Harness to port 1.
  5. Secure the FasCard reader to base as described in the FasCard Mounting Guide.

Machine Configuration


FasCard Admin Site Configuration

Use the following settings depending on the Machine Start Harness used.

Pulse (C-5256)

  1. Equipment Type: SingleVend
  2. Pulse Length: 55