Page tree
Skip to end of metadata
Go to start of metadata

Overview

Equipment Details


Average Installation Time


On This Page

Make: [VARIES]
TEST F2 Reader Installation Guides


TODO


Known Models

DCTD30KCS10EC
DCTD30KCS15EC
DCTD80KCA15EC
DCTD80KCS15EC
DCTD80KCS15EC
DCTD80KCS15EC
DCTD80KCS15EC
DCTD80KCS15EC
DCTD80KCS15EC
DCTD80KCS15EC
DCTD80KCS15EC
DCTD80KCS15EC
DCTD80KCS15EC
DCTD80KCS15EC
DCTD80KCS15EC
DCTD80KCS15EC
DCTD80KCS15ECTS
DCTD80KCS15ECTS
DCTD80KCS15ECTS
DCTD80KCS15ECTS
DCTD80KCS15ECTS
DCTD80KCS15ECTS
DCTD80KCS15ECTS
DCTD80KCS15ECTS
DCTD80KCS15ECTS
DCTG80KCS
DCWD 80KCS15EC
DCWD55KCS
DCWD55KCS10TS
DCWD55KCS10TS
DCWD55KCS10TS
DCWD55KCS10TS
DCWD80KCS15
DCWD80KCS15
DCWD80KCS15CN
DCWD80KCS15CN
DCWD80KCS15CN
DCWD80KCS15EC
DCWD80KCS15EC
DCWD80KCS15EC
DCWD80KCS15EC
DCWD80KCS15EC
DCWD80KCS15EC
DCWD80KCS65EC
DCWD80KCSTS
DCWD80KCSTS
DCWD80KCSTS
DCWD80KCW
DCWD80KCW15EC
DCWD80KCW15EC
DCWD80KCW15EC
DCWD80KCW65EC
DCWD80KCW65EC
DCWD80KCW65EC
DCWD80KCY15CN
TEST F2 Reader Installation Guides

This document assumes the installer has working knowledge of hand tools and of the target machine in question. Physical modification of machine may be required, including modification of machine panels and internal modification to accommodate cables or harnesses. It is recommended that the instructions contained herein be performed by individuals who are qualified to perform these tasks. Card Concepts Inc. takes no responsibility for the accuracy of this document or for any damage that may occur to target machine.

Required Hardware

Card Reader

One of the following readers.

Part IDDescriptionImage
C-3001
LC WiFi Reader
Front/Vertical Mount
C-3002
LC WiFi Reader
Top/Horizontal Mount
C-5401
F2 FasCard Reader
Front Mount
C-5402
F2 FasCard Reader
High Front/Top Mount
C-5403
FLEX Reader
Front/Vertical Mount
C-5404
FLEX Reader
Top/Horizontal Mount

Recommended Tools and Supplies (Not Included)

See 0808 F2 Reader Install Guide for more information.

Installation

    Page not found for multiexcerpt macro.
The page: null was not found. Please check/update the page name used in the 'multiexcerpt-include' macro.

Install Mounting Hardware

Coin and Card

P/N: C-5710
Rubber Grommet
3/4"
Qty: 1
P/N: C-6801
F2 Reader Mounting Kit
Universal
Qty: 1

  1. Place the C-6700-TEMP Drill Template on the desired mounting location.

  2. Verify included harnesses will reach desired location without encountering interference from internal machine components.

  3. Refer to FasCard Mounting Guide for further instructions.

Card Only - Easy Card Prepped Models

P/N: C-5035
Label
3-7/8" x 3-1/4"
Qty: 1
P/N: C-5710
Rubber Grommet
3/4"
Qty: 1
P/N: C-6801
F2 Reader Mounting Kit
Universal
Qty: 1

  1. Place C-5035 Label over card slot.
  2. Place the C-6700-TEMP Drill Template on the desired mounting location.

  3. Verify included harnesses will reach desired location without encountering interference from internal machine components.

  4. Refer to FasCard Mounting Guide for further instructions.

Connect Power

P/N: C-5211
Power Adapter Harness
CGI - AC
Qty: 1
P/N: C-5500-60
Power Extension Harness
60"
Qty: 1
P/N: C-5602R1
Power Converter
SMT-012-018VW
Qty: 1

  1. Tap power as described in the Fascard Reader Install - Universal Concepts document by connecting the C-5211 Power Adapter Harness to the male spade connectors on the machine power panel.
    1. Connect the green wire to the ground terminal.
    2. A corner of the power panel cover may need to be bent slightly to allow the power harness egress.
  2. Connect the opposite end of the C-5211 Power Adapter Harness to the C-5602 Power Converter.
  3. Connect the C-5500-60 Power Extension Harness to the appropriate connector on the C-5602 Power Converter. The remaining cable end connects to the FasCard reader.

Connect Coin Sense Harness

Coin Drop: Factory

P/N: C-6253
Coin Sense Harness
28"
Qty: 1

  1. Disconnect the Coin Drop from the Machine Control Assembly.
  2. Connect the C-6253 Coin Sense Harness to the harness connected to the Coin Drop.

Connect Machine Interface Harness

Pulse

P/N: C-5256
Machine Start Harns (pulse)
20" - Male taps, Rq. Female
Qty: 1

  1. Connect the C-5256 Machine Start Harness to the Coin Drop Harness previously connected to the coin drop.

Connect and Mount Reader

Item No.ComponentNotes
1Power Connection PortUtilizes the same power harnesses as the first generation FasCard reader.
2Pulse Connection PortConnection point for pulse machine start harnesses.
3Coin 1 Connection PortThis is the connection point for the harness input associated with Coin 1.
4Coin 2 Connection PortThis is the connection point for the harness input associated with Coin 2.
5Serial Connection PortThis is the connection point for serial machine start harnesses.

  1. Feed remaining harness ends through the mounting hole as described in the F1: FasCard Reader Mounting Guide.
  2. Connect the free end of the C-5256 Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.
  3. Connect the free end of the C-6253 Coin Sense Harness to port 3 (Coin Sense Harness Connection Port) as shown in the image above.
  4. Connect the free end of the C-5500-60 Power Harness to port 1.
  5. Secure the FasCard reader to base as described in the FasCard Mounting Guide.

Machine Configuration

TODO

FasCard Admin Site Configuration

Use the following settings depending on the Machine Start Harness used.

Pulse (C-5256)

  1. Equipment Type: SingleVend
  2. Pulse Length: 55