Page tree
Skip to end of metadata
Go to start of metadata

Overview

Equipment Details


Average Installation Time


On This Page

Make: [VARIES]
TEST F2 Reader Installation Guides


TODO


Known Models

BWNBC2PP112TW01
BWNSX2PP112CW01
GWNMN2PP112TW01
GWNSX299112TW01
GWNSX2PP112TW01
GWNSX2PP302AW01
HWNBC2PP112TW01
HWNBY2PP112PW01
HWNBY2PP112TW01
HWNSX2PP112TQ01
HWNSX2PP112TW01
HWNSX2SP112CW01
PWNBC2PP112TG02
SWNBC2PP112TG02
SWNBC2SP112TQ01
SWNBC2SP112TW01
SWNBC2ST112TW01
SWNBY2PP112TW01
SWNLC2SP111TW01
SWNLX2SP111TW01
SWNLY2PP112TW01
SWNSX2PP112TQ01
SWNSX2PP112TW01
SWNSX2PP112TW02
SWNSX2SP112TQ01
SWNSX2SP112TW01
SWNSX2SP112TW02
TEST F2 Reader Installation Guides

This document assumes the installer has working knowledge of hand tools and of the target machine in question. Physical modification of machine may be required, including modification of machine panels and internal modification to accommodate cables or harnesses. It is recommended that the instructions contained herein be performed by individuals who are qualified to perform these tasks. Card Concepts Inc. takes no responsibility for the accuracy of this document or for any damage that may occur to target machine.

Required Hardware

Card Reader

One of the following readers.

Part IDDescriptionImage
C-3001
LC WiFi Reader
Front/Vertical Mount
C-3002
LC WiFi Reader
Top/Horizontal Mount
C-5401
F2 FasCard Reader
Front Mount
C-5402
F2 FasCard Reader
High Front/Top Mount
C-5403
FLEX Reader
Front/Vertical Mount
C-5404
FLEX Reader
Top/Horizontal Mount

Recommended Tools and Supplies (Not Included)

See 3314 F2 Reader Install Guide for more information.

Installation

    Page not found for multiexcerpt macro.
The page: null was not found. Please check/update the page name used in the 'multiexcerpt-include' macro.

Install Mounting Hardware

Coin and Card

P/N: C-6801
F2 Reader Mounting Kit
Universal
Qty: 1

  1. Place the C-6700-TEMP Drill Template on the desired mounting location.

  2. Verify included harnesses will reach desired location without encountering interference from internal machine components.

  3. Refer to FasCard Mounting Guide for further instructions.

Card Only - Coin Slide Metercase

P/N: C-0301
Topload Mounting Bolt
Qty: 1
P/N: C-6760
Metercase Bracket
Coin Slide Ready Machine
Qty: 1
P/N: C-6801
F2 Reader Mounting Kit
Universal
Qty: 1

  1. Remove existing coin box and coin slide.

  2. Attach C-5414 Standard Bracket to the C-6760 Metercase Bracket using the C-5702 Chase Nipple and C-5703 Nut.

  3. Insert C-6760 Metercase Bracket into the metercase and secure using C-0301 Topload Mounting Bolt.

Connect Power

P/N: C-5101
Spade Taps
18-14 AWG
Qty: 3
P/N: C-5210
Power Adapter Harness
CGI
Qty: 1
P/N: C-5500
Power Extension Harness
25.5"
Qty: 1
P/N: C-5602R1
Power Converter
SMT-012-018VW
Qty: 1

  1. Tap power as described in the Fascard Reader Install - Universal Concepts document using the C-5101 Spade Taps provided.
  2. Connect the C-5210 Power Adapter Harness to the installed spade taps. Connect the opposite end to the C-5602 Power Converter.
  3. Connect the C-5500 Power Extension Harness to the appropriate connector on the C-5602 Power Converter. The remaining cable end connects to the FasCard reader.

Connect Coin Sense Harness

Coin Drop: Hybrid Coin Slide

P/N: C-6253
Coin Sense Harness
28"
Qty: 1

  1. Disconnect the Coin Drop from the Machine Control Assembly.
  2. Connect the C-6253 Coin Sense Harness to the Microswitch mounted behind the coin slide.

Coin Drop: Optical Coin

P/N: C-6250
Coin Sense Harness
can use C-6250-144
Qty: 1

  1. Disconnect the Coin Drop from the Machine Control Assembly.
  2. Connect the C-6250 Coin Sense Harness to the harness connected to the Coin Drop.

Connect Machine Interface Harness

Pulse - Hybrid Coin Slide

P/N: C-5256
Machine Start Harns (pulse)
20" - Male taps, Rq. Female
Qty: 1

  1. Connect the C-5256 Machine Start Harness to the harness previously connected to the Microswitch.

Pulse - Optical Coin

P/N: C-5300-NC
Machine Start Harness
can use C-5300-NC-144
Qty: 1

  1. Connect the C-5300-NC Machine Start Harness to the Coin 1 connector on the Machine Control Assembly.

Serial

P/N: C-0110-CP
Jumper Plug
Enables card mode on pre-ACA
Qty: 1
P/N: C-0110-TOP
Machine Start Harness
can use C-0110-TOP-144
Qty: 1

  1. Connect the C-0110-TOP Machine Start Harness to the H3 connector on the Machine Control Assembly.
  2. Connect the C-0110-CP Jumper Plug to the H6 connection on the Machine Control Assembly.

Connect and Mount Reader

Item No.ComponentNotes
1Power Connection PortUtilizes the same power harnesses as the first generation FasCard reader.
2Pulse Connection PortConnection point for pulse machine start harnesses.
3Coin 1 Connection PortThis is the connection point for the harness input associated with Coin 1.
4Coin 2 Connection PortThis is the connection point for the harness input associated with Coin 2.
5Serial Connection PortThis is the connection point for serial machine start harnesses.

  1. Feed remaining harness ends through the mounting hole as described in the FasCard Mounting Guide.
  2. Connect the free end of the Machine Start Harness.
    1. If following steps for a serial Machine Start Harness to port 5 (Serial Connection Port) as shown in the image above.
    2. If following steps for a pulse Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.
  3. Connect the free end of the Coin Sense Harness to port 3 (Coin 1 Sense Harness Connection Port) as shown in the image above.
  4. Connect the free end of the Power Extension Harness to port 1 (Power Harness Connection Port) as shown in the image above.
  5. Secure the FasCard reader to base as described in the FasCard Mounting Guide.

Machine Configuration

TODO

FasCard Admin Site Configuration

Use the following settings depending on the Machine Start Harness used.

Pulse (C-5300-NC & C-5256)

  1. Equipment Type: SingleVend
  2. Pulse Length: 80

Serial (C-0110-TOP)

  1. Equipment Type: