Page tree
Skip to end of metadata
Go to start of metadata

Overview

Equipment Details


Average Installation Time


On This Page

Make: Maytag
bypass
TEST F2 Reader Installation Guides


TODO


Known Models

MFR20PDCTS
MFR30PDCTS
MFR35PDCTS
MFR40PDCTS
MFR50PDCTS
MFR60PDCTS
MFR60PDCTS/25001210VT
MFR80PDCTS
TEST F2 Reader Installation Guides

This document assumes the installer has working knowledge of hand tools and of the target machine in question. Physical modification of machine may be required, including modification of machine panels and internal modification to accommodate cables or harnesses. It is recommended that the instructions contained herein be performed by individuals who are qualified to perform these tasks. Card Concepts Inc. takes no responsibility for the accuracy of this document or for any damage that may occur to target machine.

Required Hardware

Card Reader

One of the following readers.

Part IDDescriptionImage
C-3001
LC WiFi Reader
Front/Vertical Mount
C-3002
LC WiFi Reader
Top/Horizontal Mount
C-5401
F2 FasCard Reader
Front Mount
C-5402
F2 FasCard Reader
High Front/Top Mount
C-5403
FLEX Reader
Front/Vertical Mount
C-5404
FLEX Reader
Top/Horizontal Mount

Recommended Tools and Supplies (Not Included)

See 3407 F2 Reader Install Guide for more information.

Installation

    Page not found for multiexcerpt macro.
The page: null was not found. Please check/update the page name used in the 'multiexcerpt-include' macro.

Install Mounting Hardware

Coin and Card

P/N: C-6801
F2 Reader Mounting Kit
Universal
Qty: 1

  1. Place the C-6700-TEMP Drill Template on the desired mounting location.

  2. Verify included harnesses will reach desired location without encountering interference from internal machine components.

  3. Refer to FasCard Mounting Guide for further instructions.

Card Only - Small Coin Vault (MFR18PD and MFR25PD Models)

P/N: C-0914
Mounting Bracket
Maytag
Qty: 1
P/N: C-0940
Vault Cover
3-7/8" x 2-3/4"
Qty: 1
P/N: C-1063
Screw
8-32" x 3/8" - Kep
Qty: 2
P/N: C-1066
Nut
M3.5 - Kep
Qty: 4
P/N: C-6701
Adapter Plate
F1 to F2
Qty: 1
P/N: C-6801
F2 Reader Mounting Kit
Universal
Qty: 1

  1. Remove coin drop and coin box.

  2. Attach C-6701 Adapter Plate to C-0914 Mounting Bracket using C-1063 Kep Screws.
  3. Place the C-5414 Standard Bracket over the C-6701 Adapter Plate so the holes line up and attach together using the C-5702 Chase Nipple and C-5703 Nut.
  4. Install C-0914 Mounting Bracket where the coin drop was originally mounted. Secure in place using C-1066 Kep Nuts.
  5. Spread the inner tabs outward on the C-0940 Vault cover and install into the coin vault.

Card Only - Large Coin Vault (MFR30PD, MFR40PD, MFR60PD, MFR80PD Models)

P/N: C-0914
Mounting Bracket
Maytag
Qty: 1
P/N: C-0941
Vault Cover
3-7/8" x 3-1/2"
Qty: 1
P/N: C-1063
Screw
8-32" x 3/8" - Kep
Qty: 2
P/N: C-1066
Nut
M3.5 - Kep
Qty: 4
P/N: C-6701
Adapter Plate
F1 to F2
Qty: 1
P/N: C-6801
F2 Reader Mounting Kit
Universal
Qty: 1

  1. Remove coin drop and coin box.

  2. Attach C-6701 Adapter Plate to C-0914 Mounting Bracket using C-1063 Kep Screws.
  3. Place the C-5414 Standard Bracket over the C-6701 Adapter Plate so the holes line up and attach together using the C-5702 Chase Nipple and C-5703 Nut.
  4. Install C-0914 Mounting Bracket where the coin drop was originally mounted. Secure in place using C-1066 Kep Nuts.
  5. Spread the inner tabs outward on the C-0941 Vault cover and install into the coin vault.

Connect Power

P/N: C-5101
Spade Taps
18-14 AWG
Qty: 3
P/N: C-5210
Power Adapter Harness
CGI
Qty: 1
P/N: C-5500
Power Extension Harness
25.5"
Qty: 1
P/N: C-5602R1
Power Converter
SMT-012-018VW
Qty: 1

  1. Tap power as described in the Fascard Reader Install - Universal Concepts document using the C-5101 Spade Taps provided.
  2. Connect the C-5210 Power Adapter Harness to the installed spade taps. Connect the opposite end to the C-5602 Power Converter.
  3. Connect the C-5500 Power Extension Harness to the appropriate connector on the C-5602 Power Converter. The remaining cable end connects to the FasCard reader.

Connect Coin Sense Harness

Coin Drop: Factory

P/N: C-6360
Coin Sense Harness
Female taps, Rq. Male
Qty: 1

  1. Disconnect the Red, Blue, and (2) Green wires from the coin drop termination block spade connections and connect the C-6360 Coin Sense Harness in place of the disconnected wires, matching the corresponding colors.

Connect Machine Interface Harness

Pulse

P/N: C-5364
Machine Start Harness
Maytag MFR
Qty: 1

  1. Connect the C-5364 Machine Start Harness to the Debit connection on the Machine Control Assembly.

Connect and Mount Reader

Item No.ComponentNotes
1Power Connection PortUtilizes the same power harnesses as the first generation FasCard reader.
2Pulse Connection PortConnection point for pulse machine start harnesses.
3Coin 1 Connection PortThis is the connection point for the harness input associated with Coin 1.
4Coin 2 Connection PortThis is the connection point for the harness input associated with Coin 2.
5Serial Connection PortThis is the connection point for serial machine start harnesses.

  1. Feed remaining harness ends through the mounting hole as described in the F1: FasCard Reader Mounting Guide.
  2. Connect the free end of the C-5364 Machine Start Harness to port 5 (Serial Connection Port) as shown in the image above.
  3. Connect the free end of the C-6360 Coin Sense Harness to port 3 (Coin Sense Harness Connection Port) as shown in the image above.
  4. Connect the free end of the C-5500 Power Harness to port 1.
  5. Secure the FasCard reader to base as described in the FasCard Mounting Guide.

Machine Configuration

TODO

FasCard Admin Site Configuration

Use the following settings depending on the Machine Start Harness used.

Pulse (C-5364)

  1. Equipment Type: SingleVend
  2. Pulse Length: 24

  • No labels