Page tree
Skip to end of metadata
Go to start of metadata

Overview

Equipment Details


Average Installation Time


On This Page

Make: [VARIES]
Washer: Alliance ACA Front-Load Washer - Quantum+
Dryer: Alliance ACA Small Dryer - Quantum+
TEST F2 Reader Installation Guides


TODO


Known Models

HTENXASP133DW01
HTENXASP133FW01
HTENXASP283CW01
HTENXASP293CW01
HTENXASP543DW01
HTENYASP283CW01
HTENYASP293CW01
HTGNXASP093CW01
HTGNXASP113FW01
HTGNXASP123DW01
HTGNXASP543DW01
STENCASP173TW01
STENCASP175TW01
STENXASP133DW01
STENXASP133FW01
STENXASP173TW01
STENXASP175TW01
STENXASP283CW01
STENXASP293CW01
STENXASP433AW01
STENXASP543DN01
STENXASP543DW01
STENYASP173TN01
STENYASP173TW01
STENYASP175TW01
STENYASP283CW01
STENYASP293CW01
STGNCASP113TW01
STGNCASP115TW01
STGNXASG113JW01
STGNXASG113TW01
STGNXASG115TW01
STGNXASP093CW01
STGNXASP113FW01
STGNXASP113TW01
STGNXASP123DW01
STGNXASP303AW01
STGNXASP543DN01
STGNXASP543DW01
STGNYASA115TW01
STGNYASP093CW01
STGNYASP113TN01
STGNYASP113TW01
STGNYASP115TW01
STGNYAST115GW01
STGNYFFT115TW01
STGNYFSP115TW01
STLNYASP543PW01
TEST F2 Reader Installation Guides

This document assumes the installer has working knowledge of hand tools and of the target machine in question. Physical modification of machine may be required, including modification of machine panels and internal modification to accommodate cables or harnesses. It is recommended that the instructions contained herein be performed by individuals who are qualified to perform these tasks. Card Concepts Inc. takes no responsibility for the accuracy of this document or for any damage that may occur to target machine.

Required Hardware

Card Reader

One of the following readers.

Part IDDescriptionImage
C-3001
LC WiFi Reader
Front/Vertical Mount
C-3002
LC WiFi Reader
Top/Horizontal Mount
C-5401
F2 FasCard Reader
Front Mount
C-5402
F2 FasCard Reader
High Front/Top Mount
C-5403
FLEX Reader
Front/Vertical Mount
C-5404
FLEX Reader
Top/Horizontal Mount

Recommended Tools and Supplies (Not Included)

See 3421 F2 Reader Install Guide for more information.

Installation

    Page not found for multiexcerpt macro.
The page: null was not found. Please check/update the page name used in the 'multiexcerpt-include' macro.

Install Mounting Hardware

Coin and Card

P/N: C-6801
F2 Reader Mounting Kit
Universal
Qty: 1

  1. Place the C-6700-TEMP Drill Template on the desired mounting location.

  2. Verify included harnesses will reach desired location without encountering interference from internal machine components.

  3. Refer to FasCard Mounting Guide for further instructions.

Card Only - Card Ready

P/N: C-6801
F2 Reader Mounting Kit
Universal
Qty: 1

  1. Place the C-6700-TEMP Drill Template on the desired mounting location.

  2. Verify included harnesses will reach desired location without encountering interference from internal machine components.

  3. Refer to FasCard Mounting Guide for further instructions.

Card Only - Coin Ready

P/N: C-1059
Nut
10-32 - Kep
Qty: 2
P/N: C-1070-W
Washer - Build: XCH
1/4" x 1" O.D.
Qty: 2
P/N: C-5365
Bypass Harness
Alliance Coin Vault Bypass
Qty: 1
P/N: C-6765-W
F2 Mounting Bracket
10 Degree - White Finish
Qty: 1
P/N: C-6801
F2 Reader Mounting Kit
Universal
Qty: 1

  1. Remove existing coin box and coin drop.

  2. Install the C-5365 Bypass Harness by removing the coin vault switch and connecting the spade terminal connections to C-5365 Bypass Harness.
  3. Install the C-6765-W Metercase Bracket and secure to the machine using the C-1059 Kep Nut and C-1070-W Washer.

  4. Attach the C-5414 F2 Mounting Bracket to the C-6765-W Metercase Bracket using C-5702 Chase Nipple and C-5703 Lock Nut.

Connect Power

P/N: C-6204-40
Power Adapter Harness
F2, 12vDC Pow Harness - 40"
Qty: 1

  1. Connect the C-6204-40 12VDC Power Harness to the H10 Connection on the Machine Control Assembly.
    1. Connect the green wire to a chassis ground.
  2. The remaining end (3-pin molex) connects directly to the rear of the F2 FasCard Reader.

Connect Coin Sense Harness

Coin Drop: Factory

P/N: C-6250
Coin Sense Harness
can use C-6250-144
Qty: 1

  1. Disconnect the Coin Drop from the Machine Control Assembly.
  2. Connect the C-6250 Coin Sense Harness to the harness connected to the Coin Drop.

Connect Machine Interface Harness

Pulse

P/N: C-5300-NC
Machine Start Harness
can use C-5300-NC-144
Qty: 1

  1. Connect the C-5300-NC Machine Start Harness to the coin 1 connector on the Machine Control Assembly.

Serial

P/N: C-5240
Machine Start Harness
can use C-5240-144
Qty: 1

  1. Connect the C-5240 Machine Start Harness to the H3 connector on the Machine Control Assembly.

Connect and Mount Reader

Item No.ComponentNotes
1Power Connection PortUtilizes the same power harnesses as the first generation FasCard reader.
2Pulse Connection PortConnection point for pulse machine start harnesses.
3Coin 1 Connection PortThis is the connection point for the harness input associated with Coin 1.
4Coin 2 Connection PortThis is the connection point for the harness input associated with Coin 2.
5Serial Connection PortThis is the connection point for serial machine start harnesses.

  1. Feed remaining harness ends through the mounting hole as described in the FasCard Mounting Guide.
  2. Connect the free end of the Machine Start Harness.
    1. If following steps for a serial Machine Start Harness to port 5 (Serial Connection Port) as shown in the image above.
    2. If following steps for a pulse Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.
  3. Connect the free end of the Coin Sense Harness to port 3 (Coin Sense Harness Connection Port) as shown in the image above.
  4. Connect the free end of the Power Extension Harness to port 1 (C-5500 Power Harness Connection Port) as shown in the image above.
  5. Secure the FasCard reader to base as described in the FasCard Mounting Guide.

Machine Configuration

TODO

FasCard Admin Site Configuration

Use the following settings depending on the Machine Start Harness used.

Pulse (C-5300-NC)

  1. Equipment Type: SingleVend
  2. Pulse Length: 80

Serial (C-5240)

  1. Equipment Type: 
    1. Washer: Alliance ACA H7S Front Load Washer A4 - Quantum+
    2. Dryer: Alliance ACA H7S Small Dryer A4 - Quantum+