Page tree
Skip to end of metadata
Go to start of metadata

Overview

Equipment Details


Average Installation Time


On This Page

Make: [VARIES]
Alliance ACA Top-Load Washer
bypass
TEST F2 Reader Installation Guides


TODO


Known Models

HWNBC2PP115TW01
HWNBY2PP115TW01
HWNBY2PT115TW01
HWNBY2SB115EW01
HWNBY2SP115TW01
HWNKC210115TW01
HWNKC2P1115TW01
HWNKC2SP115PW01
HWNKC2SP115TW01
HWNKC2ST115PW01
HWNKC2ST115TW01
HWNKE2SP115CW01
HWNKE2SP115EW01
HWNKX2SP115CW01
HWNKY2SB115CW01
HWNKY2SP115CW01
HWNKY2ST115CW01
HWNSX2PP115TW01
KWNBX2SP115TW01
KWNSX2PP115TW01
KWNSX2SP115TW01
PWNBC2PP115TW02
PWNBX2PP115TG02
SWNNC25P113TW01
SWNNC2HP113TW15
SWNNC2HP115TW 02
SWNNC2HP115TW01
SWNNC2HP115TW02
SWNNC2HT115TW01
SWNNC2SP113TQ01
SWNNC2SP113TW01
SWNNC2SP113TW02
SWNNC2SP115TQ01
SWNNC2SP115TW01
SWNNC2SP115TW02
SWNNX2AP113TW15
SWNNX2HP115TW01
SWNNX2SP113TW02
SWNNX2SP115CW01
SWNNX2SP115TW01
SWNNX2SP115TW02
SWNNY2HP115TW01
SWNNY2SG115TW01
SWNNY2SP113TW01
SWNNY2SP115PW01
SWNNY2SP115TW01
SWNNY2ST113TW01
SWNNY2ST115TW01
SWNSX2SP115TW01
SWNSX2SP115TW02
TEST F2 Reader Installation Guides

This document assumes the installer has working knowledge of hand tools and of the target machine in question. Physical modification of machine may be required, including modification of machine panels and internal modification to accommodate cables or harnesses. It is recommended that the instructions contained herein be performed by individuals who are qualified to perform these tasks. Card Concepts Inc. takes no responsibility for the accuracy of this document or for any damage that may occur to target machine.

Required Hardware

Card Reader

One of the following readers.

Part IDDescriptionImage
C-3001
LC WiFi Reader
Front/Vertical Mount
C-3002
LC WiFi Reader
Top/Horizontal Mount
C-5401
F2 FasCard Reader
Front Mount
C-5402
F2 FasCard Reader
High Front/Top Mount
C-5403
FLEX Reader
Front/Vertical Mount
C-5404
FLEX Reader
Top/Horizontal Mount

Recommended Tools and Supplies (Not Included)

See 3569 F2 Reader Install Guide for more information.

Installation

    Page not found for multiexcerpt macro.
The page: null was not found. Please check/update the page name used in the 'multiexcerpt-include' macro.

Install Mounting Hardware

Coin and Card

P/N: C-6801
F2 Reader Mounting Kit
Universal
Qty: 1

  1. Place the C-6700-TEMP Drill Template on the desired mounting location.

  2. Verify included harnesses will reach desired location without encountering interference from internal machine components.

  3. Refer to FasCard Mounting Guide for further instructions.

Card Only - Card Ready Models

P/N: C-5420
Screw
10-32 x ¼" - Pan
Qty: 6
P/N: C-5763
F1/F2 Alliance TL CO Mount
Qty: 1
P/N: C-6801
F2 Reader Mounting Kit
Universal
Qty: 1

  1. Place C-5763 TWL Bracket in the intended mounting location. Using the bracket, mark the location of all four mounting holes.
  2. Drill a hole at each marked location using a 3/16" drill bit.
  3. Attach C-5414 Mounting Bracket to the front of C-5763 using two C-5420 screws
  4. Mount the C-5763 TLW Bracket using four C-5420 Screws and fasten from the inside of the panel.

Card Only - Coin Ready Models (Standard Metercase)

P/N: C-1059
Nut
10-32 - Kep
Qty: 2
P/N: C-1070-W
Washer - Build: XCH
1/4" x 1" O.D.
Qty: 2
P/N: C-5760-A
Alliance Adapter Bracket
Mounts C-5760 to MeterCase
Qty: 1
P/N: C-6760
Metercase Bracket
Coin Slide Ready Machine
Qty: 1
P/N: C-6801
F2 Reader Mounting Kit
Universal
Qty: 1

  1. Remove existing coin box and coin drop.

  2. Attach C-5760-A Alliance Adapter Bracket to C-6760 Metercase Bracket.
  3. Attach the C-5414 Mounting Bracket to C-6760 Metercase Bracket and secure with C-5702 Chase Nipple and C-5703 Nut.
  4. Mount C-6760 Metercase Bracket into the front of the metercase, inserting the two studs through the coin slot openings.
    1. Secure to the metercase using C-1059 Kep Nuts and C-1070-W Washers.

Card Only - Coin Ready Models (High Capacity Metercase)

P/N: C-1059
Nut
10-32 - Kep
Qty: 2
P/N: C-1070-W
Washer - Build: XCH
1/4" x 1" O.D.
Qty: 2
P/N: C-5365
Bypass Harness
Alliance Coin Vault Bypass
Qty: 1
P/N: C-5760-A
Alliance Adapter Bracket
Mounts C-5760 to MeterCase
Qty: 1
P/N: C-6762
Metercase Bracket
Coin Slide Ready Machine
Qty: 1
P/N: C-6801
F2 Reader Mounting Kit
Universal
Qty: 1

  1. Remove existing coin box and coin drop.

  2. Bridge the Coin Vault Switch connections using C-5365 Bypass Harness.
  3. Attach C-5760-A Alliance Adapter Bracket to C-6762 Metercase Bracket.
  4. Attach the C-5414 Mounting Bracket to C-6762 Metercase Bracket and secure with C-5702 Chase Nipple and C-5703 Nut.
  5. Mount C-6762 Metercase Bracket into the front of the metercase, inserting the two studs through the coin slot openings.
    1. Secure to the metercase using C-1059 Kep Nuts and C-1070-W Washers.

Connect Power

P/N: C-6204-40
Power Adapter Harness
F2, 12vDC Pow Harness - 40"
Qty: 1

  1. Connect the C-6204-40 12VDC Power Harness to the H10 connection on the machine control assembly

    1. Secure the green wire beneath the ground screw.

  2. Connect the opposite end of the C-6204-40  Power Adapter Harness (3-pin molex) to the F2 reader.

Connect Coin Sense Harness

Coin Drop: Optical Coin Sensor

P/N: C-6250
Coin Sense Harness
can use C-6250-144
Qty: 1

  1. Disconnect the Coin Drop from the Machine Control Assembly.
  2. Connect the C-6250 Coin Sense Harness to the harness connected to the Coin Drop.

Coin Drop: Hybrid Coin Slide

P/N: C-6253
Coin Sense Harness
28"
Qty: 1

  1. Disconnect the harness from micro switch.
  2. Connect both ends of C-6253 Coin Sense Harness to the micro switch.

Connect Machine Interface Harness

Pulse - Hybrid Coin Slide

P/N: C-5256
Machine Start Harns (pulse)
20" - Male taps, Rq. Female
Qty: 1

  1. Connect the C-5256 Machine Start Harness to the manufacturer's harness previously connected to the micro switch used by the coin slide.

Serial

P/N: C-5240
Machine Start Harness
can use C-5240-144
Qty: 1

  1. Connect the C-5240 Machine Start Harness to the H3 connection on the Machine Control Assembly.

Connect and Mount Reader

Item No.ComponentNotes
1Power Connection PortUtilizes the same power harnesses as the first generation FasCard reader.
2Pulse Connection PortConnection point for pulse machine start harnesses.
3Coin 1 Connection PortThis is the connection point for the harness input associated with Coin 1.
4Coin 2 Connection PortThis is the connection point for the harness input associated with Coin 2.
5Serial Connection PortThis is the connection point for serial machine start harnesses.

  1. Feed remaining harness ends through the mounting hole as described in the 3569 F2 Reader Install Guide.
  2. Connect the free end of the Machine Start Harness.
    1. For Hybrid Coin Slide models, connect C-5256 to port 2 (Pulse Connection Port) as shown in the image above.
    2. For all other models, connect C-5240 to port 5 (Serial Connection Port) as shown in the image above.
  3. Connect the free end of the Coin Sense Harness to port 3 (Coin Sense Harness Connection Port) as shown in the image above.
  4. Connect the free end of the C-6204-40 Power Harness to port 1.
  5. Secure the FasCard reader to base as described in the FasCard Mounting Guide.

Machine Configuration

TODO

FasCard Admin Site Configuration

Use the following settings depending on the Machine Start Harness used.

Pulse (C-5256)

  1. Equipment Type: SingleVend
  2. Pulse Length: 80

Pulse (C-5240)

  1. Equipment Type: SingleVend
  2. Pulse Length: 80

Serial (C-5240)

  1. Equipment Type: Alliance ACA H7S Top Load Washer