Page tree
Skip to end of metadata
Go to start of metadata

Overview

Equipment Details


Average Installation Time


On This Page

Make: [VARIES]
Alliance ACA Tumbler Dryer (Single)
TEST F2 Reader Installation Guides


TODO


Known Models

HT030NBYW0NBG3W000
HT050NWCANBG3NC0A0
HT055NBCANBG3W0000
HT075LBCF3G2W00000
HT075NBCANXG3N0000
HT075NBCB1G1W03000
HT075NBY0NBG3W0000
HT075NNC0NBG3NC000
HT075NNCANBG3NC000
HT075NNCANBGSN0000
HT075NNCANXG3N0000
HT075NNCANXG3NC0C0
HT075NNCANXG3W0000
HT075NWCANBG3N0000
HT075NWCANBG3N00C0
HT075NWCANXG3NC000
HT075NWCANXG3NC0C0
HT075NWCANXG5NC0
HT075NWCANXG5NC0A0
HT075NWCARBS5NC000
HT075NWY0NBG3N0000
HT075NWY0NBG3N00A0
HT075NWY0NBG3N00C0
HT075NWY0NBG3NC0A0
HT075NWY0NBG3NC0C0
HT075NWY0NBS3N0000
HT075NWY0NXG3N0000
HT075NWY0NXG3N00A0
HT075NWY0NXG3NC0A0
HT075NWY0NXG3W0000
HT075NWY0RBG3NC0A0
HT075NWY0RBG3NC0C0
HT075NWY0RXS5NC0C0
HT075NWYORXS5NC000
HT075NWYORXS5NC0C0
KT030NBCANXS3WA000
KT055NNCARXS3W00
KT055NNCARXS3W0000
KT075NBCARXH3N0000
KT075NBY0NXH3N0000
KT075NNCANXH3N00
KT075NNCARBH3W00
KT075NNCARBH3W000
KT075NNCARXH3N0000
KT075NNCARXS3W0000
KT075NNY0RNH3N00
KT075NNY0RNH3N0000
KT075NNY0RNH3N00000
KT075NNY0RNH3N00000000
PT075NNCANBG3N0000
ST030NBDANBG3WA000
ST030NWDANBG3WA000
ST050NNCANBG3W0000
ST055EWY0NDG3W0000
ST055NWDANBG3WA000
ST075LNCARBS5NC000
ST075NBCANBG3W0000
ST075NNCANBG3N0000
ST075NNCANXG3N0000
ST075NNDANBG3N0000
ST075NNY0NXG3N0000
ST075NWCANBG3N0000
ST075NWCANBG3W0000
ST075NWCANXG3N0000
ST075NWCARBG3W0000
ST075NWCARXG3N0000
ST075NWX0NBG3N0000
TEST F2 Reader Installation Guides

This document assumes the installer has working knowledge of hand tools and of the target machine in question. Physical modification of machine may be required, including modification of machine panels and internal modification to accommodate cables or harnesses. It is recommended that the instructions contained herein be performed by individuals who are qualified to perform these tasks. Card Concepts Inc. takes no responsibility for the accuracy of this document or for any damage that may occur to target machine.

Required Hardware

Card Reader

One of the following readers.

Part IDDescriptionImage
C-3001
LC WiFi Reader
Front/Vertical Mount
C-3002
LC WiFi Reader
Top/Horizontal Mount
C-5401
F2 FasCard Reader
Front Mount
C-5402
F2 FasCard Reader
High Front/Top Mount
C-5403
FLEX Reader
Front/Vertical Mount
C-5404
FLEX Reader
Top/Horizontal Mount

Recommended Tools and Supplies (Not Included)

See 3571 F2 Reader Install Guide for more information.

Installation

    Page not found for multiexcerpt macro.
The page: null was not found. Please check/update the page name used in the 'multiexcerpt-include' macro.

Install Mounting Hardware

Coin and Card

P/N: C-6801
F2 Reader Mounting Kit
Universal
Qty: 1

  1. Place the C-6700-TEMP Drill Template on the desired mounting location.

  2. Verify included harnesses will reach desired location without encountering interference from internal machine components.

  3. Refer to F2 FasCard Reader Mounting Guide for further instructions.

Card Only - Coin Ready Models

P/N: C-0144
Screw
8-32 x 2" - Flat
Qty: 2
P/N: C-5033
Label
4-5/8" x 3-1/2"
Qty: 1
P/N: C-5365
Bypass Harness
Alliance Coin Vault Bypass
Qty: 1
P/N: C-6601
Spacer
F2 Dexter Vault Filler Plate
Qty: 1
P/N: C-6602
F2, Large Vault Mount
Qty: 1
P/N: C-6801
F2 Reader Mounting Kit
Universal
Qty: 1

  1. Remove existing coin box.

  2. Remove Vault Switch and bridge the wires previously connected to the Vault Switch with the C-5365 Bypass Harness.
  3. Bend the side tabs of the C-6602 Vault Bracket outward and install into the coin vault. The tabs should snap into place securing the bracket.

  4. Before securing the reader to the machine with C-0144 Screws, place the C-0906 Spacer between the reader and machine so the Screws pass through the circular holes in the Spacer.

Card Only - Card Ready Models

P/N: C-1060
Screw - Build: TK
8-32 x 3/8" - Zinc
Qty: 2
P/N: C-6801
F2 Reader Mounting Kit
Universal
Qty: 1
P/N: C-6970
F2, Bracket
Alliance Card Ready
Qty: 1

  1. Install the C-6970 Alliance Mounting Bracket into the opening on the control panel for mounting card readers and coin drops.
  2. Attach the C-5414 F2 Mounting Bracket to the C-6970 Alliance Mounting Bracket and secure using the C-1060 Screws.
  3. Refer to F2 FasCard Reader Mounting Guide for further instructions.

Connect Power

P/N: C-6204-40
Power Adapter Harness
F2, 12vDC Pow Harness - 40"
Qty: 1

  1. Connect the C-6204-40 Power Adapter Harness (12VDC power) to the H10 connection on the Machine Control Assembly.

    1. Secure the green wire beneath the ground screw.

Connect Coin Sense Harness

Coin Drop: Factory

P/N: C-6250
Coin Sense Harness
can use C-6250-144
Qty: 1

  1. Disconnect the coin drop from the machine control assembly. 
  2. Connect the C-6250 Coin Sense Harness to the harness connected to the coin drop. 

Coin Drop: Factory - Dual Coin

P/N: C-6250
Coin Sense Harness
can use C-6250-144
Qty: 2

  1. Disconnect the Coin Drop from the Machine Control Assembly.
  2. Connect a C-6250 Coin Sense Harness to the harness connected to the Coin 1 Drop.
  3. Connect a C-6250 Coin Sense Harness to the harness connected to the Coin 2 Drop.

Connect Machine Interface Harness

Pulse and Serial

P/N: C-5240
Machine Start Harness
can use C-5240-144
Qty: 1

  1. Connect the C-5240 Machine Start Harness to the H3 connector on the Machine Control Assembly.

Connect and Mount Reader

Item No.ComponentNotes
1Power Connection PortUtilizes the same power harnesses as the first generation FasCard reader.
2Pulse Connection PortConnection point for pulse machine start harnesses.
3Coin 1 Connection PortThis is the connection point for the harness input associated with Coin 1.
4Coin 2 Connection PortThis is the connection point for the harness input associated with Coin 2.
5Serial Connection PortThis is the connection point for serial machine start harnesses.

  1. Feed remaining harness ends through mounting hole as described in F2 FasCard Reader Mounting Guide.
  2. Connect the free end of the C-5240 Machine Start Harness to port 5 (Serial Connection Port) as shown in the image above.
  3. Connect the free end of the C-6250 Coin Sense Harness to port 3 (Coin 1 Sense Harness Connection Port) as shown in the image above.
    1. If using a dual coin drop, connect the second C-6250 Coin Sense Harness to port 4 (Coin 2 Sense Harness Connection Port) as shown in the image above.
  4. Connect the free end of the C-6204-40 Power Extension Harness to port 1 (Power Harness Connection Port) as shown in the image above.
  5. Connect FasCard reader to base as described in the F2 FasCard Reader Mounting Guide.

Machine Configuration

ACA machines using a serial configuration require dip switch 3 on the Machine Control Board to be set to the 'ON' position. Leave all other dip switches as is.

FasCard Admin Site Configuration

Use the following settings depending on the Machine Start Harness used.

Pulse (C-5240)

  1. Equipment Type: SingleVend
  2. Pulse Length: -80

Serial (C-5240)

  1. Equipment Type: Alliance ACA H7S Tumbler Dryer