Page tree
Skip to end of metadata
Go to start of metadata

Overview

Equipment Details


Average Installation Time


On This Page

Make: [VARIES]
Alliance ACA Tumbler Dryer (Single)
TEST F1 Reader Installation Guides


TODO


Known Models

HT030NBYW0NBG3W000
HT050NWCANBG3NC0A0
HT055NBCANBG3W0000
HT075LBCF3G2W00000
HT075NBCANXG3N0000
HT075NBCB1G1W03000
HT075NBY0NBG3W0000
HT075NNC0NBG3NC000
HT075NNCANBG3NC000
HT075NNCANBGSN0000
HT075NNCANXG3N0000
HT075NNCANXG3NC0C0
HT075NNCANXG3W0000
HT075NWCANBG3N0000
HT075NWCANBG3N00C0
HT075NWCANXG3NC000
HT075NWCANXG3NC0C0
HT075NWCANXG5NC0
HT075NWCANXG5NC0A0
HT075NWCARBS5NC000
HT075NWY0NBG3N0000
HT075NWY0NBG3N00A0
HT075NWY0NBG3N00C0
HT075NWY0NBG3NC0A0
HT075NWY0NBG3NC0C0
HT075NWY0NBS3N0000
HT075NWY0NXG3N0000
HT075NWY0NXG3N00A0
HT075NWY0NXG3NC0A0
HT075NWY0NXG3W0000
HT075NWY0RBG3NC0A0
HT075NWY0RBG3NC0C0
HT075NWY0RXS5NC0C0
HT075NWYORXS5NC000
HT075NWYORXS5NC0C0
KT030NBCANXS3WA000
KT055NNCARXS3W00
KT055NNCARXS3W0000
KT075NBCARXH3N0000
KT075NBY0NXH3N0000
KT075NNCANXH3N00
KT075NNCARBH3W00
KT075NNCARBH3W000
KT075NNCARXH3N0000
KT075NNCARXS3W0000
KT075NNY0RNH3N00
KT075NNY0RNH3N0000
KT075NNY0RNH3N00000
KT075NNY0RNH3N00000000
PT075NNCANBG3N0000
ST030NBDANBG3WA000
ST030NWDANBG3WA000
ST050NNCANBG3W0000
ST055EWY0NDG3W0000
ST055NWDANBG3WA000
ST075LNCARBS5NC000
ST075NBCANBG3W0000
ST075NNCANBG3N0000
ST075NNCANXG3N0000
ST075NNDANBG3N0000
ST075NNY0NXG3N0000
ST075NWCANBG3N0000
ST075NWCANBG3W0000
ST075NWCANXG3N0000
ST075NWCARBG3W0000
ST075NWCARXG3N0000
ST075NWX0NBG3N0000
TEST F1 Reader Installation Guides



This document assumes the installer has working knowledge of hand tools and of the target machine in question. Physical modification of machine may be required, including modification of machine panels and internal modification to accommodate cables or harnesses. It is recommended that the instructions contained herein be performed by individuals who are qualified to perform these tasks. Card Concepts Inc. takes no responsibility for the accuracy of this document or for any damage that may occur to target machine.

Required Hardware

Card Reader

Part IDDescriptionImage
C-5001
F1 FasCard Reader

Recommended Tools and Supplies (Not Included)

See 3571 FasCard F1 Install Guide for more information.

Installation

    Page not found for multiexcerpt macro.
The page: null was not found. Please check/update the page name used in the 'multiexcerpt-include' macro.

Install Mounting Hardware

Coin and Card - Coin Ready 

P/N: C-5801
F1 Reader Mounting Kit
Front
Qty: 1

  1. Place the C-5700-TEMP Drill Template on the desired mounting location.

  2. Verify included harnesses will reach desired location without encountering interference from internal machine components.

  3. Refer to FasCard Mounting Guide for further instructions.

Card Only - Coin Ready 

P/N: C-0133
Standoff
8-32" x 1-1/2" - Hex
Qty: 2
P/N: C-0144
Screw
8-32 x 2" - Flat
Qty: 2
P/N: C-0906
Spacer Plate
5 1/2" x 4 3/8"
Qty: 1
P/N: C-0936
Vault Mount Bracket
Qty: 1
P/N: C-5027
Label
Credit Card Logo
Qty: 1
P/N: C-5365
Bypass Harness
Alliance Coin Vault Bypass
Qty: 1

  1. Remove existing coin box.

  2. Remove Vault Switch and bridge the wires previously connected to the Vault Switch with the C-5365 Bypass Harness.
  3. Bend the side tabs of the C-0936 Bracket outward and install into the coin vault. The tabs should snap into place securing the bracket.

  4. Attach the C-0133 Standoffs to the Bracket.

  5. Before securing the reader to the machine with C-0144 Screws, place the C-0906 Spacer between the reader and machine so the Screws pass through the circular holes in the Spacer.

Card Only - Card Ready 

P/N: C-0970
Mounting Bracket
Multi-Purpose
Qty: 1
P/N: C-5027
Label
Credit Card Logo
Qty: 1
P/N: C-5751
Screw
8-32 x 2-1/2" - Flat
Qty: 2

  1. Remove factory payment device bracket from the machine.
  2. Install the C-0970 Mounting Bracket where the payment device bracket was previously. Use the existing hardware to secure bracket.

Connect Power

P/N: C-6204-40
Power Adapter Harness
F2, 12vDC Pow Harness - 40"
Qty: 1

  1. Connect the C-6204-40 Power Adapter Harness (12VDC power) to the H10 connection on the Machine Control Assembly.

    1. Secure the green wire beneath the ground screw.

Connect Coin Sense Harness

Coin Drop: Factory

P/N: C-5250
Coin Sense Harness
Qty: 1

  1. Disconnect the coin drop from the machine control assembly. 
  2. Connect the C-5250 Coin Sense Harness to the harness connected to the coin drop. 

Connect Machine Interface Harness

Pulse and Serial

P/N: C-5240
Machine Start Harness
can use C-5240-144
Qty: 1

  1. Connect the C-5240 Machine Start Harness to the H3 connection on the Machine Control Assembly.

Connect and Mount Reader

    Page not found for multiexcerpt macro.
The page: null was not found. Please check/update the page name used in the 'multiexcerpt-include' macro.

  1. Feed remaining harness ends through the mounting hole as described in the F1: FasCard Reader Mounting Guide.
  2. Connect the free end of the C-5240 Machine Start Harness to port 1 (Serial Connection Port) as shown in the image above.
  3. Connect the free end of the C-5250 Coin Sense Harness to port 3 (Coin Sense Harness Connection Port) as shown in the image above.
  4. Connect the free end of the C-6204-40 Power Extension Harness to port 4 (Power Harness Connection Port) as shown in the image above.
  5. Secure the FasCard reader to base as described in the FasCard Mounting Guide.

Machine Configuration

ACA machines using a serial configuration require dip switch 3 on the Machine Control Board to be set to the 'ON' position. Leave all other dip switches as is.

FasCard Admin Site Configuration

Use the following settings depending on the Machine Start Harness used.

Pulse (C-5240)

  1. Equipment Type: SingleVend
  2. Pulse Length: -80

Serial (C-5240)

  1. Equipment Type:Alliance ACA H7S

    Page not found for multiexcerpt macro.
The page: null was not found. Please check/update the page name used in the 'multiexcerpt-include' macro.