Page tree
Skip to end of metadata
Go to start of metadata

On this Page

Overview and Equipment Information

This document is intended to guide the user through installation utilizing the kit numbered according to the document title. A list of associated equipment models including control information and additional installation notes can be found below.

Kit Installation Notes

Status: Active

Product: FasCard F1
Manufacturer: Vending
Start Harness: 6-pin (2x3) molex connector
Interface Type: Serial
Install Type: Card Only
Actuation: Card Ready
Coin Sense: N/A
Mounting: Custom Bracket
Chassis: Vending Machine
Readers: 1 Reader
Machine Control: Vending MDB Level 1


This document assumes the installer has working knowledge of hand tools and of the target machine in question. Physical modification of machine may be required, including modification of machine panels and internal modification to accommodate cables or harnesses. It is recommended that the instructions contained herein be performed by individuals who are qualified to perform these tasks. Card Concepts Inc. takes no responsibility for the accuracy of this document or for any damage that may occur to target machine.

Required Hardware

Card Reader

Part IDDescriptionImage
C-5001
F1 FasCard Reader


Installation Kit

QTYPart NumberDescriptionImage
1C-0124-MLVMachine Start Harness
1C-0972Mounting Bracket
1C-5021Label
1C-5027Label
3C-5101Spade Taps
1C-5210Power Adapter Harness
1C-5500-60Power Extension Harness
1C-5602Power Converter
2C-5751Screw

Recommended Tools and Supplies (Not Included)

See F1: FasCard Reader Mounting Guide for more information.

Installation

Confirm machine power is disconnected before beginning installation!

Use caution and appropriate protection to prevent hand and eye injury during installation!

Step 1 - Install Mounting Bracket

C-0972
Mounting Bracket

  1. Remove existing card reader bezel, and attach the C-0972 Mounting Bracket.

Step 2 - Connect Power

C-5101C-5210C-5500-60C-5602
Spade Taps
Power Adapter Harness
Power Extension Harness
Power Converter

  1. Tap power as described in the Fascard Reader Install - Universal Concepts document using the C-5101 Spade Taps provided.
  2. Connect the C-5210 Power Adapter Harness to the installed spade taps. Connect the opposite end to the C-5602 Power Converter.
  3. Connect the C-5500-60 Power Extension Harness to the appropriate connector on the C-5602 Power Converter. The remaining cable end connects to the FasCard reader.

Step 3 - Connect Machine Interface Harness

C-0124-MLV
Machine Start Harness

  1. Connect the C-0124-MLV Machine Interface Harness to the harness/connector where the Coin Drop/Bill Validator normally connects.
  2. Connect the remaining end of the C-0124-MLV Machine Interface Harness to the harness where the Coin Drop was previously connected.

Step 4 - Connect and Mount FasCard Reader

C-0124-MLVC-5500-60
Machine Start Harness
Power Extension Harness

  1. Feed remaining harness ends through mounting hole as described in F1: FasCard Reader Mounting Guide.
  2. Connect the free end of the C-0124-MLV Machine Interface Harness to port 1 (Serial Connection Port) as shown in the image above.
  3. Connect the free end of the C-5500-60 Power Extension Harness to port 4 (C-5500 Power Harness Connection Port) as shown in the image above.
  4. Connect FasCard reader to base as described in the FasCard Mounting Guide.
  5. Program the card reader address as described here: How to Program Address on a FasCard Reader.

Associated Equipment Models

MakeModelControlNotes
Vend-RiteVM240D*Vending - MDB Level 1
Vend-RiteVM360C*Vending - MDB Level 1Notes
Vend-RiteVM360D*Vending - MDB Level 1