Page tree
Skip to end of metadata
Go to start of metadata
Table of Contents
Overview and Equipment Information

This document is intended to guide the user through installation utilizing the kit numbered according to the document title. A list of associated equipment models including control information and additional installation notes can be found below.

Kit Installation Notes

Status: Active

Product: FasCard F1
Manufacturer: Alliance
Start Harness: 7-pin single row flat connector
Interface Type: Serial
Install Type: Coin and Card
Actuation: Coin Drop - Factory
Coin Sense: N/A
Mounting: Surface Mount
Chassis: N/A
Readers: 1 Reader
Machine Control: Alliance MDC/Centurion


This document assumes the installer has working knowledge of hand tools and of the target machine in question. Physical modification of machine may be required, including modification of machine panels and internal modification to accommodate cables or harnesses. It is recommended that the instructions contained herein be performed by individuals who are qualified to perform these tasks. Card Concepts Inc. takes no responsibility for the accuracy of this document or for any damage that may occur to target machine.

Required Hardware

Card Reader

Part IDDescriptionImage
C-5001
F1 FasCard Reader

Install Kit (K-5704-CO)

QTYPart NumberDescriptionImage
1C-0110-CPJumper Plug
1C-0110-TOPMachine Start Harness
3C-5101Spade Taps
1C-5210Power Adapter Harness
1C-5250Coin Sense Harness
1C-5500Power Extension Harness
1C-5602Power Converter
1C-5800F1 Reader Mounting Kit

Recommended Tools and Supplies

See F1: FasCard Reader Mounting Guide for more information.


Installation

Confirm machine power is disconnected before beginning installation!

Use caution and appropriate protection to prevent hand and eye injury during installation!

Step 1 - Install Mounting Bracket

C-5700-TEMPC-5800
Drill Template
F1 Reader Mounting Kit

  1. Place the C-5700-TEMP Drill Template on the desired mounting location.
  2. Verify included harnesses will reach desired location without encountering interference from internal machine components.
  3. Refer to F1: FasCard Reader Mounting Guide for further instructions.

Step 2 - Connect Power

C-5101C-5210C-5500C-5602
Spade Taps
Power Adapter Harness
Power Extension Harness
Power Converter

  1. Tap power as described in the Fascard Reader Install - Universal Concepts document using the C-5101 Spade Taps provided.
  2. Connect the C-5210 Power Adapter Harness to the installed spade taps. Connect the opposite end to the C-5602 Power Converter.
  3. Connect the C-5500 Power Extension Harness to the appropriate connector on the C-5602 Power Converter. The remaining cable end connects to the FasCard reader.

Step 3 - Connect Coin Sense Harness

C-5250
Coin Sense Harness

  1. Disconnect the Coin Drop from the Machine Control Assembly.
  2. Connect the C-5250 Coin Sense Harness to the harness connected to the Coin Drop.

Step 4 - Connect Machine Start Harness

C-0110-CPC-0110-TOP
Jumper Plug
Machine Start Harness

  1. Remove the existing Alliance Jumper Plug at H8 and connect the C-0110-CP Jumper Plug to the Machine Control Assembly.
  2. Connect the C-0110-TOP Machine Start Harness to the Machine Control Assembly at H5.
    1. The opposite end of this harness connects directly to the FasCard reader.

Step 5 - Connect and Mount FasCard Reader

C-0110-TOPC-5250C-5500
Machine Start Harness
Coin Sense Harness
Power Extension Harness

  1. Feed harness ends through mounting hole as described in the FasCard Mounting Guide.
  2. Connect the C-0110-TOP Machine Start Harness to port 1 (Serial Communication Port) as shown in the image above.
  3. Connect the free end of the C-5250 Coin Sense Harness to port 3 (Coin Sense Harness Connection Port) as shown in the image above.
  4. Connect the C-5500 Power Extension Harness to port 4 (C-5500 Power Harness Connection Port) as shown in the image above.
  5. Connect FasCard reader to base as described in the F1: FasCard Reader Mounting Guide.
  6. Program the card reader address as described here: How to Program Address on a FasCard Reader.


Associated Equipment Models

MakeModelControlNotes
HuebschHD#BCA####1#W01Alliance MDC Small Dryer
HuebschHDET07WFAlliance MDC Small Dryer
HuebschHDGT09#FAlliance MDC Small Dryer
HuebschHF#BCF####2#N01Alliance MDC Front Load Washer
HuebschHF#BCF####2#W01Alliance MDC Front Load Washer
HuebschHFNCCFSGWAlliance MDC Front Load Washer
HuebschHW#BC2####2#Q01Alliance MDC Top Load Washer
HuebschHW#BC2####2#W01Alliance MDC Top Load Washer
HuebschHWFT####Alliance MDC Front Load Washer
HuebschHWTT20WNAlliance MDC Top Load Washer
IPSOBD#BCA####1#W01Alliance MDC Small Dryer
IPSOBF#B?F####?#N01Alliance MDC Front Load Washer
IPSOBF#B?F####?#W01Alliance MDC Front Load WasherNotes
IPSOBWTT20WNAlliance MDC Top Load Washer
PrimusPWNBC2PP112TG02Alliance MDC Top Load Washer
Speed QueenSCN###JC#######Alliance Centurion Washer Extractor C2.5 - Quantum Silver
Speed QueenSD#BCA####1#W01Alliance MDC Small Dryer
Speed QueenSF#BCF####2#W01Alliance MDC Front Load Washer
Speed QueenSF#L#F####1#N01Alliance Centurion Front Load Washer C4 - Quantum Gold
Speed QueenSF#LCF######W01Alliance Centurion Front Load Washer C4 - Quantum Gold
Speed QueenSS#BCA####1#W01Alliance MDC Small Dryer
Speed QueenSW#BC2####2#W01Alliance MDC Top Load Washer
Speed QueenSWFT7#*NAlliance MDC Front Load Washer
Speed QueenSWFX71#NAlliance MDC Front Load Washer
Speed QueenSWTT2##NAlliance MDC Top Load Washer