Page tree
Skip to end of metadata
Go to start of metadata

On this Page

Overview and Equipment Information

This document is intended to guide the user through installation utilizing the kit numbered according to the document title. A list of associated equipment models including control information and additional installation notes can be found below.

Kit Installation Notes

Status: Active

Product: FasCard F1
Manufacturer: Alliance
Start Harness: 7-pin single row flat connector
Interface Type: Serial
Install Type: Coin and Card
Actuation: Coin Drop - Factory
Coin Sense: N/A
Mounting: Surface Mount
Chassis: N/A
Readers: 1 Reader
Machine Control: Alliance MDC/Centurion

This document assumes the installer has working knowledge of hand tools and of the target machine in question. Physical modification of machine may be required, including modification of machine panels and internal modification to accommodate cables or harnesses. It is recommended that the instructions contained herein be performed by individuals who are qualified to perform these tasks. Card Concepts Inc. takes no responsibility for the accuracy of this document or for any damage that may occur to target machine.

Required Hardware

Card Reader

Part IDDescriptionImage
F1 FasCard Reader

Installation Kit

QTYPart NumberDescriptionImage
1C-0110-CPJumper Plug
1C-0110-TOPMachine Start Harness
1C-5205R2Power Adapter Harness
1C-5250Coin Sense Harness
1C-5800F1 Reader Mounting Kit

Recommended Tools and Supplies (Not Included)

See F1 Reader Mounting Guide for more information.


Confirm machine power is disconnected before beginning installation!

Use caution and appropriate protection to prevent hand and eye injury during installation!

Step 1 - Install Mounting Bracket

Drill Template
F1 Reader Mounting Kit

  1. Place the C-5700-TEMP Drill Template on the desired mounting location.
  2. Verify included harnesses will reach desired location without encountering interference from internal machine components.
  3. Refer to FasCard Mounting Guide for further instructions.

Step 2 - Connect Power

Power Adapter Harness

  1. Connect the C-5250R2 Power Adapter Harness to the machine 24vac power connector.
    1. Secure the ground wire to a screw located near the rear of the control pan.

Step 3 - Connect Coin Sense Harness

Coin Sense Harness

  1. Disconnect the Coin Drop from the Machine Control Assembly.
  2. Connect the C-5250 Coin Sense Harness to the harness connected to the Coin Drop.

Step 4 - Connect Machine Start Harness

Jumper Plug
Machine Start Harness

  1. Remove the existing Alliance Jumper Plug at H8 and connect the C-0110-CP Jumper Plug to the Machine Control Assembly.
  2. Connect the C-0110-TOP Machine Start Harness to the Machine Control Assembly at H5.
    1. The opposite end of this harness connects directly to the FasCard reader.

Step 5 - Connect and Mount FasCard Reader

Machine Start Harness
Coin Sense Harness

  1. Feed remaining harness ends through mounting hole as described in F1 Reader Mounting Guide.
  2. Connect the free end of the C-0110-TOP Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.
  3. Connect the free end of the C-5250 Coin Sense Harness to port 3 (Coin Sense Harness Connection Port) as shown in the image above.
  4. Connect the free end of the C-5250R2 Power Adapter Harness to port 4 (C-5500 Power Harness Connection Port) as shown in the image above.
  5. Connect FasCard reader to base as described in the FasCard Mounting Guide.
  6. Program the card reader address as described here: How to Program Address on a FasCard Reader.

Associated Equipment Models

HuebschHCN###??#######Alliance Centurion Washer Extractor C3 - Galaxy 600
HuebschHCN###KD#######Alliance Centurion Washer Extractor C3 - Galaxy 600
HuebschHCN###KE#######Alliance Centurion Washer Extractor C3 - Galaxy 600
IPSOICN###KC#######Alliance Centurion Washer Extractor C3 - Maestro V
Speed QueenSCN###??#######Alliance Centurion Washer Extractor C4 - Quantum Gold
Speed QueenSCN###?E#######Alliance Centurion Washer Extractor C4 - Quantum Gold