Page tree
Skip to end of metadata
Go to start of metadata

On this Page

Overview and Equipment Information

This document is intended to guide the user through installation utilizing the kit numbered according to the document title. A list of associated equipment models including control information and additional installation notes can be found below.

Kit Installation Notes

Status: Active

Product: FasCard F1
Manufacturer: Alliance
Start Harness: 7-pin single row flat connector
Interface Type: Serial
Install Type: Card Only
Actuation: N/A
Coin Sense: N/A
Mounting: Coin Vault
Chassis: N/A
Readers: 1 Reader
Machine Control: Alliance MDC/Centurion


This document assumes the installer has working knowledge of hand tools and of the target machine in question. Physical modification of machine may be required, including modification of machine panels and internal modification to accommodate cables or harnesses. It is recommended that the instructions contained herein be performed by individuals who are qualified to perform these tasks. Card Concepts Inc. takes no responsibility for the accuracy of this document or for any damage that may occur to target machine.

Required Hardware

Card Reader

Part IDDescriptionImage
C-5001
F1 FasCard Reader

Installation Kit

QTYPart NumberDescriptionImage
1C-0110-CPJumper Plug
1C-0110-TOPMachine Start Harness
2C-0133Standoff
2C-0144Screw
1C-0936Vault Mount Bracket
1C-5021Label
1C-5027Label
1C-5205R2Power Adapter Harness
1C-5365Bypass Harness

Recommended Tools and Supplies (Not Included)

See F1 Reader Mounting Guide for more information.

Installation

Confirm machine power is disconnected before beginning installation!

Use caution and appropriate protection to prevent hand and eye injury during installation!

Step 1 - Install Mounting Bracket

C-0936
Vault Mount Bracket

  1. Insert the C-0970 Vault Mount Bracket into the Coin Vault
  2. Spread the bracket wings to lock it into place.

Step 2 - Connect Power

C-5205R2
Power Adapter Harness

  1. Connect the C-5250R2 Power Adapter Harness to the machine 24vac power connector.
    1. Secure the ground wire to a screw located near the rear of the control pan.

Step 3 - Connect Machine Start Harness

C-0110-CPC-0110-TOPC-5365
Jumper Plug
Machine Start Harness
Bypass Harness

  1. Remove the existing Alliance Jumper Plug at H8 and connect the C-0110-CP Jumper Plug to the Machine Control Assembly.
  2. Connect the C-0110-TOP Machine Start Harness to the Machine Control Assembly at H5.
    1. The opposite end of this harness connects directly to the FasCard reader.
  3. Connect the C-5365 Bypass Harness to the appropriate connections to bypass the Coin Box.

Step 4 - Connect and Mount FasCard Reader

C-0110-TOPC-5205R2C-5250
Machine Start Harness
Power Adapter Harness
Coin Sense Harness

  1. Feed remaining harness ends through mounting hole as described in F1 Reader Mounting Guide.
  2. Connect the free end of the C-0110-TOP Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.
  3. Connect the free end of the C-5250 Coin Sense Harness to port 3 (Coin Sense Harness Connection Port) as shown in the image above.
  4. Connect the free end of the C-5250R2 Power Adapter Harness to port 4 (C-5500 Power Harness Connection Port) as shown in the image above.
  5. Connect FasCard reader to base as described in the FasCard Mounting Guide.
  6. Program the card reader address as described here: How to Program Address on a FasCard Reader.

Associated Equipment Models

MakeModelControlNotes
Speed QueenSCN###??#######Alliance Centurion Washer Extractor C4 - Quantum Gold
Speed QueenSF#BCF####2#W01Alliance MDC Front Load Washer