Page tree
Skip to end of metadata
Go to start of metadata

On this Page

Overview and Equipment Information

This document is intended to guide the user through installation utilizing the kit numbered according to the document title. A list of associated equipment models including control information and additional installation notes can be found below.

Kit Installation Notes

Status: Active

Product: FasCard F1
Manufacturer: Alliance
Start Harness: 7-pin single row flat connector
Interface Type: Serial
Install Type: Card Only
Actuation: Card Ready
Coin Sense: N/A
Mounting: Custom Bracket
Chassis: Stack Large Chassis
Readers: 2 Readers
Machine Control: Alliance MDC/Centurion

This document assumes the installer has working knowledge of hand tools and of the target machine in question. Physical modification of machine may be required, including modification of machine panels and internal modification to accommodate cables or harnesses. It is recommended that the instructions contained herein be performed by individuals who are qualified to perform these tasks. Card Concepts Inc. takes no responsibility for the accuracy of this document or for any damage that may occur to target machine.

Required Hardware

Card Reader

Part IDDescriptionImage
F1 FasCard Reader

Installation Kit

QTYPart NumberDescriptionImage
2C-0110-CPJumper Plug
2C-0110-TOPMachine Start Harness
2C-0970Mounting Bracket
1C-5338Power Adapter Harness
1C-5500-60Power Extension Harness
1C-5500-84Power Extension Harness
1C-5501Y Power Adapter Harness
1C-5602Power Converter

Recommended Tools and Supplies (Not Included)

See FasCard Mounting Guide for more information.


Confirm machine power is disconnected before beginning installation!

Use caution and appropriate protection to prevent hand and eye injury during installation!

Step 1 - Install Mounting Bracket

Mounting Bracket

  1. Install the C-0970 Mounting Bracket on the back of the control panel.
  2. Mount the FasCard reader to the panel using provided hardware.

Step 2 - Connect Power

Power Adapter Harness
Power Extension Harness
Power Extension Harness
Y Power Adapter Harness
Power Converter

  1. Tap power as described in the Fascard Reader Install - Universal Concepts document by connecting directly to the power terminals at L1 and L2.
  2. Connect the C-5338 Power Adapter Harness to the installed spade taps. Connect the opposite end to the C-5602 Power Converter.
  3. Connect the C-5500-84  Power Extension Harness to the appropriate connector on the C-5602 Power Converter.
  4. Connect the C-5501 Y Adapter Harness to the remaining end of the C-5500-84 Power Extension Harness. One end of the C-5501 Y Adapter Harness connects to a FasCard reader.
  5. Connect the C-5500-60 Power Extension Harness to the remaining end of the C-5501 Y Adapter Harness. The remaining end of the C-5500-60 Power Extension Harness connects to a FasCard reader.

Step 3 - Connect Machine Start Harness

Jumper Plug
Machine Start Harness

  1. Connect the C-0110-TOP Machine Start Harness to the Machine Control Assembly at the position marked H3.
  2. Connect the C-0110-CP Jumper Plug to the Machine Control Assembly at the position marked H6.

Step 4 - Connect and Mount FasCard Reader

Machine Start Harness
Power Extension Harness
Power Extension Harness

  1. Feed remaining harness ends through mounting hole as described in FasCard Mounting Guide.
  2. Connect the free end of the C-0110-TOP Machine Start Harness to port 1 (Serial Connection Port) as shown in the image above.
  3. Connect the C-5500-84 and C-5500-60 Power Extension Harness to port 4 (C-5500 Power Harness Connection Port) as shown above.
  4. Connect FasCard reader to base as described in the FasCard Mounting Guide.
  5. Program the card reader address as described here: How to Program Address on a FasCard Reader.

Associated Equipment Models

ContinentalKTT###BY#######Alliance MDC Tumbler Dryer
Speed QueenSTT###BY#######Alliance MDC Tumbler Dryer