Page tree
Skip to end of metadata
Go to start of metadata

On this Page

Overview and Equipment Information

This document is intended to guide the user through installation utilizing the kit numbered according to the document title. A list of associated equipment models including control information and additional installation notes can be found below.

Kit Installation Notes

Status: Active

Product: FasCard F1
Manufacturer: Alliance
Start Harness: 7-pin single row flat connector
Interface Type: Serial
Install Type: Card Only
Actuation: Coin Drop - Factory
Coin Sense: Optical Eye
Mounting: Metercase Bracket
Chassis: Small Chassis - Rear Control
Readers: 1 Reader
Machine Control: Alliance ACA


ACA machines using a serial configuration require dip switch 3 on the Machine Control Board to be set to the 'ON' position. Leave all other dip switches as is.

This document assumes the installer has working knowledge of hand tools and of the target machine in question. Physical modification of machine may be required, including modification of machine panels and internal modification to accommodate cables or harnesses. It is recommended that the instructions contained herein be performed by individuals who are qualified to perform these tasks. Card Concepts Inc. takes no responsibility for the accuracy of this document or for any damage that may occur to target machine.

Required Hardware

Card Reader

Part IDDescriptionImage
C-5001
F1 FasCard Reader

Installation Kit

QTYPart NumberDescriptionImage
2C-0141Screw
2C-1059Nut
2C-1070-WWasher - Build: XCH
1C-5021Label
1C-5027Label
1C-5240Machine Start Harness
1C-5760-AAlliance Adapter Bracket
1C-5762Metercase Bracket - High Cap
1C-6204-40Power Adapter Harness

Recommended Tools and Supplies (Not Included)

See F1 Reader Mounting Guide for more information.

Installation

Confirm machine power is disconnected before beginning installation!

Use caution and appropriate protection to prevent hand and eye injury during installation!

Step 1 - Install Mounting Bracket

C-1059C-1070-WC-5760-AC-5762
Nut
Washer - Build: XCH
Alliance Adapter Bracket
Metercase Bracket - High Cap

  1. Remove any existing Coin Drop and Coin Box.
  2. Install the C-5760-A Adapter Bracket onto the C-5762 Metercase Bracket.
  3. Install the C-5762 Metercase Bracket over the front of the Metercase and secure with C-1070-W Washer and C-1059 Nut.
  4. Refer to FasCard Mounting Guide for further information as needed.

Step 2 - Connect Power

C-6204-40
Power Adapter Harness

  1. Connect the C-6204-40 12VDC Power Harness to the H10 Connection on the Machine Control Assembly.
    1. Connect the green wire to a chassis ground.
  2. The remaining end (3-pin molex) connects directly to the rear of the F2 FasCard Reader.

Step 3 - Connect Machine Start Harness

C-5240
Machine Start Harness

  1. Connect the C-5240 Machine Start Harness to the H3 connection on the Machine Control Assembly serial port.

Step 4 - Connect and Mount FasCard Reader

C-5240C-6204
Machine Start Harness
Power Adapter Harness

  1. Feed remaining harness ends through mounting hole as described in F1 Reader Mounting Guide.
  2. Connect the free end of the C-5240 Machine Start Harness to port 1 (Serial Connection Port) as shown in the image above.
  3. Connect the free end of the C-6204 Power Extension Harness to port 4 (C-5500 Power Harness Connection Port) as shown in the image above.
  4. Connect FasCard reader to base as described in the FasCard Mounting Guide.
  5. Program the card reader address as described here: How to Program Address on a FasCard Reader.

Associated Equipment Models

MakeModelControlNotes
PrimusPWNBX2PP115TG02Alliance ACA H7S Top Load Washer A1 - MDC IINotes
Speed QueenSW#NC2####3TW##Alliance ACA H7S Top Load Washer A4 - Quantum+