Page tree
Skip to end of metadata
Go to start of metadata

On this Page

Overview and Equipment Information

This document is intended to guide the user through installation utilizing the kit numbered according to the document title. A list of associated equipment models including control information and additional installation notes can be found below.

Kit Installation Notes

Status: Active

Product: FasCard F1
Manufacturer: Laundrylux
Start Harness: 8-pin single row flat connector
Interface Type: Serial
Install Type: Coin and Card
Actuation: Coin Drop - Factory
Coin Sense: N/A
Mounting: Surface Mount
Chassis: N/A
Readers: 1 Reader
Machine Control: Laundrylux Crossover


This machine needs to be configured for Card Mode as described here: Enable Card Mode on Wascomat Crossover.

This document assumes the installer has working knowledge of hand tools and of the target machine in question. Physical modification of machine may be required, including modification of machine panels and internal modification to accommodate cables or harnesses. It is recommended that the instructions contained herein be performed by individuals who are qualified to perform these tasks. Card Concepts Inc. takes no responsibility for the accuracy of this document or for any damage that may occur to target machine.

Required Hardware

Card Reader

Part IDDescriptionImage
C-5001
F1 FasCard Reader

Installation Kit

QTYPart NumberDescriptionImage
1C-5350Power Adapter Harness
1C-5352Coin Sense Harness
1C-5355Machine Start Harness
1C-5801F1 Reader Mounting Kit

Recommended Tools and Supplies (Not Included)

See F1 Reader Mounting Guide for more information.

Installation

Confirm machine power is disconnected before beginning installation!

Use caution and appropriate protection to prevent hand and eye injury during installation!

Step 1 - Install Mounting Bracket

C-5700C-5700-TEMPC-5702C-5703
Mounting Bracket
Drill Template
Chase Nipple
Lock Nut

  1. Place the C-5700-TEMP Drill Template on the desired mounting location.
  2. Verify included harnesses will reach desired location without encountering interference from internal machine components.
  3. Refer to FasCard Mounting Guide for further instructions.

Step 2 - Connect Power

C-5350
Power Adapter Harness

  1. Connect the C-5350 Power Harness to the mated power harness inside the machine.
  2. Secure the ground wire terminal beneath a chassis screw.

Step 3 - Connect Coin Sense Harness

C-5352
Coin Sense Harness

  1. Disconnect the Coin Drop from the Machine Control Assembly.
  2. Connect the C-5352 Coin Sense Harness to the harness connected to the Coin Drop.

Step 4 - Connect Machine Start Harness

C-5355
Machine Start Harness

  1. Connect the C-5355 Machine Start Harness to the Machine Control Assembly ribbon cable.

Step 5 - Connect and Mount FasCard Reader

C-5350C-5352C-5355
Power Adapter Harness
Coin Sense Harness
Machine Start Harness

  1. Feed remaining harness ends through mounting hole as described in F1 Reader Mounting Guide.
  2. Connect the free end of the C-5355 Machine Start Harness to port 1 (Serial Connection Port) as shown in the image above.
  3. Connect the free end of the C-5352 Coin Sense Harness to port 3 (Coin Sense Harness Connection Port) as shown in the image above.
  4. Connect the free end of the C-5350 Power Harness to port 4 (C-5500 Power Harness Connection Port) as shown in the image above.
  5. Connect FasCard reader to base as described in the FasCard Mounting Guide.
  6. Program the card reader address as described here: How to Program Address on a FasCard Reader.

Associated Equipment Models

MakeModelControlNotes
WascomatWHF09810MLaundrylux CrossOver Washer
WascomatWHLFP715MLaundrylux CrossOver Washer
WascomatWHWF09810MLaundrylux CrossOver Washer
WascomatWHWF09810NMLaundrylux CrossOver Washer