Page tree
Skip to end of metadata
Go to start of metadata

On this Page

Overview and Equipment Information

This document is intended to guide the user through installation utilizing the kit numbered according to the document title. A list of associated equipment models including control information and additional installation notes can be found below.

Kit Installation Notes

Status: Active

Product: FasCard F1
Manufacturer: Laundrylux
Start Harness: 2-wire bare harness
Interface Type: Pulse
Install Type: Card Only
Actuation: N/A
Coin Sense: N/A
Mounting: Coin Vault
Chassis: N/A
Readers: 1 Reader
Machine Control: N/A


This document assumes the installer has working knowledge of hand tools and of the target machine in question. Physical modification of machine may be required, including modification of machine panels and internal modification to accommodate cables or harnesses. It is recommended that the instructions contained herein be performed by individuals who are qualified to perform these tasks. Card Concepts Inc. takes no responsibility for the accuracy of this document or for any damage that may occur to target machine.

Required Hardware

Card Reader

Part IDDescriptionImage
C-5001
F1 FasCard Reader

Installation Kit

QTYPart NumberDescriptionImage
2C-0133Standoff
2C-0141Screw
1C-0936Vault Mount Bracket
1C-5021Label
1C-5027Label
2C-5101Spade Taps
1C-5336Power Adapter Harness
1C-5356Machine Start Harns (rare)
1C-5500-84Power Extension Harness
1C-5602Power Converter

Recommended Tools and Supplies (Not Included)

See F1 Reader Mounting Guide for more information.

Installation

Confirm machine power is disconnected before beginning installation!

Use caution and appropriate protection to prevent hand and eye injury during installation!

Step 1 - Install Mounting Bracket

C-0936
Vault Mount Bracket

  1. Remove the existing Coin Vault.
  2. Insert the C-0936 Vault Mount Bracket into the machine and expand the inner wings to lock it into place.
    1. Secure standoffs before mounting reader.
  3. Refer to FasCard Mounting Guide for further instructions.

Step 2 - Connect Power

C-5101C-5336C-5500-84C-5602
Spade Taps
Power Adapter Harness
Power Extension Harness
Power Converter

  1. Tap power as described in the Fascard Reader Install - Universal Concepts document using the C-5101 Spade Taps provided.
  2. Connect the C-5336 Power Adapter Harness to the installed spade taps. Connect the opposite end to the C-5602 Power Converter.
  3. Connect the C-5500-84 Power Extension Harness to the appropriate connector on the C-5602 Power Converter. The remaining cable end connects to the FasCard reader.

Step 3 - Connect Machine Start Harness

C-5356
Machine Start Harns (rare)

  1. Connect the C-5356 Machine Start Harness to the Terminal Block on the Machine Control Assembly at positions 2 and 3 as shown above.

Step 4 - Connect and Mount FasCard Reader

C-5356C-5500-84
Machine Start Harns (rare)
Power Extension Harness

  1. Feed remaining harness ends through C-0936 Vault Mount Bracket.
  2. Connect the free end of the C-5356 Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.
  3. Connect the free end of the C-5500-84 Power Extension Harness to port 4 (C-5500 Power Harness Connection Port) as shown in the image above.
  4. Connect FasCard reader to base as described in the FasCard Mounting Guide.
  5. Program the card reader address as described here: How to Program Address on a FasCard Reader.

Associated Equipment Models

MakeModelPulse LengthSensorControlNotes
ElectroluxT4300S-500FalseSingle-Vend (Pulse)
ElectroluxT4420S-500FalseSingle-Vend (Pulse)
ElectroluxT4650-500FalseSingle-Vend (Pulse)Notes
WascomatTD30-500FalseSingle-Vend (Pulse)
WascomatTD3030-500FalseSingle-Vend (Pulse)Notes
WascomatTD4545-500FalseSingle-Vend (Pulse)Notes
WascomatTD77-500FalseSingle-Vend (Pulse)Notes