Page tree
Skip to end of metadata
Go to start of metadata

On this Page

Overview and Equipment Information

This document is intended to guide the user through installation utilizing the kit numbered according to the document title. A list of associated equipment models including control information and additional installation notes can be found below.

Kit Installation Notes

Status: Active

Product: FasCard F1
Manufacturer: Laundrylux
Start Harness: Dual Harness
Interface Type: Pulse/Serial
Install Type: Coin and Card
Actuation: Coin Drop - Factory
Coin Sense: N/A
Mounting: Surface Mount
Chassis: Stack Small Chassis
Readers: 2 Readers
Machine Control: Laundrylux Crossover


This document assumes the installer has working knowledge of hand tools and of the target machine in question. Physical modification of machine may be required, including modification of machine panels and internal modification to accommodate cables or harnesses. It is recommended that the instructions contained herein be performed by individuals who are qualified to perform these tasks. Card Concepts Inc. takes no responsibility for the accuracy of this document or for any damage that may occur to target machine.

Required Hardware

Card Reader

Part IDDescriptionImage
C-5001
F1 FasCard Reader

Installation Kit

QTYPart NumberDescriptionImage
3C-5101Spade Taps
1C-5210Power Adapter Harness
1C-5343Coin Sense Harness (SA)
1C-5344Machine Start Harness
1C-5352-40Coin Sense Harness
1C-5355Machine Start Harness
2C-5500Power Extension Harness
1C-5501Y Power Adapter Harness
1C-5602Power Converter
2C-5801F1 Reader Mounting Kit

Recommended Tools and Supplies (Not Included)

See FasCard Mounting Guide for more information.

Installation

Confirm machine power is disconnected before beginning installation!

Use caution and appropriate protection to prevent hand and eye injury during installation!

Step 1 - Install Mounting Brackets

C-5700-TEMPC-5801
Drill Template
F1 Reader Mounting Kit

  1. Place the C-5700-TEMP Drill Template on the desired mounting locations.
  2. Verify included harnesses will reach desired locations without encountering interference from internal machine components.
  3. Refer to FasCard Mounting Guide for further instructions.

Step 2 - Connect Power

C-5101C-5210C-5500C-5501C-5602
Spade Taps
Power Adapter Harness
Power Extension Harness
Y Power Adapter Harness
Power Converter

  1. Tap power as described in the Fascard Reader Install - Universal Concepts document using the C-5101 Spade Taps provided.
  2. Connect the C-5210 Power Adapter Harness to the installed spade taps. Connect the opposite end to the C-5602 Power Converter.
  3. Connect one C-5500 Power Extension Harness to the C-5501 Y Power Adapter Harness.
    1. Connect the opposite end to the C-5602 Power Converter.
  4. Connect one C-5500 Power Extension Harnesses to the remaining connector on the C-5501 Y Power Adapter Harness.
    1. The remaining connector of the C-5501 Y Power Adapter Harness and of the C-5500 Power Extension Harness connect to the installed FasCard Readers.

Step 3 - Connect Coin Sense Harnesses

C-5343C-5352-40
Coin Sense Harness (SA)
Coin Sense Harness

  1. Disconnect the Coin Drops from the Machine Control Assemblies.
  2. Connect the C-5343 Coin Sense Harness to the harness connected to the Coin Drop on the Dryer side.
  3. Connect the C-5352-40 Coin Sense Harness to the harness connected to the Coin Drop on the Washer side.

Step 4 - Connect Machine Start Harnesses

C-5344C-5355
Machine Start Harness
Machine Start Harness

  1. Connect the C-5344 Machine Start Harness to the Machine Control Assembly on the Dryer side.
  2. Connect the C-5355 Machine Start Harness to the Machine Control Assembly on the Washer side.

Step 5 - Connect and Mount FasCard Readers

C-5343C-5344C-5352-40C-5355C-5500C-5501
Coin Sense Harness (SA)
Machine Start Harness
Coin Sense Harness
Machine Start Harness
Power Extension Harness
Y Power Adapter Harness

  1. Feed remaining harness ends through mounting brackets as described in FasCard Mounting Guide.
  2. On the Dryer side reader, connect the free end of the C-5344 Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.
  3. On the Dryer side reader, connect the free end of the C-5343 Coin Sense Harness to port 3 (Coin Sense Harness Connection Port) as shown in the image above.
  4. On the Washer side reader, connect the free end of the C-5355 Machine Start Harness to port 1 (Serial Connection Port) as shown in the image above.
  5. On the Washer side reader, connect the free end of the C-5352-40 Coin Sense Harness to port 3 (Coin Sense Harness Connection Port) as shown in the image above.
  6. On both Dryer and Washer side, connect the C-5500 Power Extension Harness or C-5501 Y Power Adapter Harness to port 4 (C-5500 Power Harness Connection Port) as shown in the image above.
  7. Connect FasCard reader to base as described in the FasCard Mounting Guide.
  8. Program the card reader address as described here: How to Program Address on a FasCard Reader.

Associated Equipment Models

MakeModelPulse LengthSensorControlNotes
WascomatWDSEM?FalseSingle-Vend (Pulse)Notes