Page tree
Skip to end of metadata
Go to start of metadata

On this Page

Overview and Equipment Information

This document is intended to guide the user through installation utilizing the kit numbered according to the document title. A list of associated equipment models including control information and additional installation notes can be found below.

Kit Installation Notes

Status: Active

Product: FasCard F1
Manufacturer: Alliance
Start Harness: 7-pin single row flat connector
Interface Type: Serial
Install Type: Card Only
Actuation: N/A
Coin Sense: N/A
Mounting: Custom Bracket
Chassis: N/A
Readers: 1 Reader
Machine Control: Alliance ACA

ACA machines using a serial configuration require dip switch 3 on the Machine Control Board to be set to the 'ON' position. Leave all other dip switches as is.

This document assumes the installer has working knowledge of hand tools and of the target machine in question. Physical modification of machine may be required, including modification of machine panels and internal modification to accommodate cables or harnesses. It is recommended that the instructions contained herein be performed by individuals who are qualified to perform these tasks. Card Concepts Inc. takes no responsibility for the accuracy of this document or for any damage that may occur to target machine.

Required Hardware

Card Reader

Part IDDescriptionImage
F1 FasCard Reader

Installation Kit

QTYPart NumberDescriptionImage
2C-1070-WWasher - Build: XCH
1C-5240Machine Start Harness
1C-5765-WMounting Bracket
1C-6204Power Adapter Harness

Recommended Tools and Supplies (Not Included)

See F1 Reader Mounting Guide for more information.


Confirm machine power is disconnected before beginning installation!

Use caution and appropriate protection to prevent hand and eye injury during installation!

Step 1 - Install Mounting Bracket

Washer - Build: XCH
Mounting Bracket

  1. Remove any previously installed Coin Drop and Coin Box.
  2. Install the C-5765-W Mounting Bracket into the Coin Vault and secure by using C-1070-W Washer and C-1059 Nut.

Step 2 - Connect Power

Power Adapter Harness

  1. Connect the C-6204 12VDC Power Harness to the H10 Connection on the Machine Control Assembly.
    1. Connect the green wire to a chassis ground.
  2. The remaining end (3-pin molex) connects directly to the rear of the F2 FasCard Reader.

Step 3 - Connect Machine Start Harness

Machine Start Harness

  1. Connect the C-5240 Machine Start Harness to the Machine Control Assembly serial port.

Step 4 - Connect and Mount FasCard Reader

Machine Start Harness
Power Adapter Harness

  1. Feed remaining harness ends through mounting hole as described in F1 Reader Mounting Guide.
  2. Connect the free end of the C-5240 Machine Start Harness to port 1 (Serial Connection Port) as shown in the image above.
  3. Connect the free end of the C-6204 Power Extension Harness to port 4 (C-5500 Power Harness Connection Port) as shown in the image above.
  4. Connect FasCard reader to base as described in the FasCard Mounting Guide.
  5. Program the card reader address as described here: How to Program Address on a FasCard Reader.

Associated Equipment Models

HuebschHD#BCA#####W01Alliance ACA H7S Small Dryer A1 - MDC II
HuebschHF#BCA######W01Alliance ACA H7S Front Load Washer A1 - MDC II
HuebschHF#K#A######W##Alliance ACA H7S Front Load Washer A2 - Galaxy 600
HuebschHS#B#A#####TW01Alliance ACA H7S Small Dryer A1 - MDC II
Speed QueenSF#B#A####3#W01Alliance ACA H7S Front Load Washer A1 - MDC II
Speed QueenSF#N#A####?#W01Alliance ACA H7S Front Load Washer A4 - Quantum+Notes
Speed QueenST#NCA######W01Dual Controls (See Notes)Notes