Page tree
Skip to end of metadata
Go to start of metadata
Table of Contents
Overview and Equipment Information

This document is intended to guide the user through installation utilizing the kit numbered according to the document title. A list of associated equipment models including control information and additional installation notes can be found below.

Kit Installation Notes

Status: Active

Product: FasCard F1
Manufacturer: Alliance
Start Harness: 3-pin (1x3) molex connector
Interface Type: Pulse
Install Type: Card Only
Actuation: Coin Drop - Factory
Coin Sense: Optical Eye
Mounting: Metercase Bracket
Chassis: Small Chassis - Rear Control
Readers: 1 Reader
Machine Control: Alliance MDC/Centurion


This document assumes the installer has working knowledge of hand tools and of the target machine in question. Physical modification of machine may be required, including modification of machine panels and internal modification to accommodate cables or harnesses. It is recommended that the instructions contained herein be performed by individuals who are qualified to perform these tasks. Card Concepts Inc. takes no responsibility for the accuracy of this document or for any damage that may occur to target machine.

Required Hardware

Card Reader

Part IDDescriptionImage
C-5001
F1 FasCard Reader

Install Kit (K-5704-CO)

QTYPart NumberDescriptionImage
2C-0141Screw
2C-1059Nut
2C-1070-WWasher - Build: XCH
1C-5021Label
1C-5027Label
3C-5101Spade Taps
1C-5210Power Adapter Harness
1C-5300-NCMachine Start Harness
1C-5500Power Extension Harness
1C-5602Power Converter
1C-5761Metercase Bracket

Recommended Tools and Supplies

See F1 Reader Mounting Guide for more information.


Installation

Confirm machine power is disconnected before beginning installation!

Use caution and appropriate protection to prevent hand and eye injury during installation!

Step 1 - Install Mounting Bracket

C-5760C-0141C-1059C-1070-W
Metercase Bracket
Screw
Nut
Washer - Build: XCH

  1. Remove any existing Coin Drop.
  2. Install the C-5761 Metercase Bracket over the front of the Metercase.
  3. Refer to F1 Reader Mounting Guide for further information, as needed.

Step 2 - Connect Power

C-5101C-5210C-5500C-5602
Spade Taps
Power Adapter Harness
Power Extension Harness
Power Converter

  1. Tap power as described in the Fascard Reader Install - Universal Concepts document using the C-5101 Spade Taps provided.
  2. Connect the C-5210 Power Adapter Harness to the installed spade taps. Connect the opposite end to the C-5602 Power Converter.
  3. Connect the C-5500 Power Extension Harness to the appropriate connector on the C-5602 Power Converter. The remaining cable end connects to the FasCard reader.

Step 3 - Connect Machine Start Harness

C-5300-NC
Machine Start Harness

  1. Connect the C-5300-NC Machine Start Harness to the harness previously connected to the Coin Drop.
    1. The opposite end of this harness connects directly to the FasCard reader.

Step 4 - Connect and Mount FasCard Reader

C-5300-NCC-5500
Machine Start Harness
Power Extension Harness

  1. Feed harness ends through mounting hole as described in the FasCard Mounting Guide.
  2. Connect the C-5300-NC Machine Start Harness to port 2 (Pulse Communication Port) as shown above.
  3. Connect the C-5500 Power Extension Harness to port 4 (C-5500 Power Harness Connection Port) as shown above.
  4. Connect FasCard reader to base as described in the F1 Reader Mounting Guide.
  5. Program the card reader address as described here: How to Program Address on a FasCard Reader.



Associated Equipment Models

MakeModelPulse LengthSensorControlNotes
Speed QueenSWTX21##-80FalseSingle-Vend (Pulse)