Page tree
Skip to end of metadata
Go to start of metadata

On this Page

Overview and Equipment Information

This document is intended to guide the user through installation utilizing the kit numbered according to the document title. A list of associated equipment models including control information and additional installation notes can be found below.

Kit Installation Notes

Status: Active

Product: FasCard F1
Manufacturer: Alliance
Start Harness: 2-wire w/tap connections
Interface Type: Pulse
Install Type: Card Only
Actuation: Card Ready
Coin Sense: N/A
Mounting: Flat Mount Bezel
Chassis: Large Chassis
Readers: 1 Reader
Machine Control: N/A


This document assumes the installer has working knowledge of hand tools and of the target machine in question. Physical modification of machine may be required, including modification of machine panels and internal modification to accommodate cables or harnesses. It is recommended that the instructions contained herein be performed by individuals who are qualified to perform these tasks. Card Concepts Inc. takes no responsibility for the accuracy of this document or for any damage that may occur to target machine.

Required Hardware

Card Reader

Part IDDescriptionImage
C-5001
F1 FasCard Reader

Installation Kit

QTYPart NumberDescriptionImage
2C-0122Spade Taps
2C-0141Screw
1C-0935Mounting Bracket
1C-5021Label
1C-5027Label
3C-5101Spade Taps
1C-5210Power Adapter Harness
1C-5305Machine Start Harness
1C-5500Power Extension Harness
1C-5602Power Converter

Recommended Tools and Supplies (Not Included)

See FasCard Mounting Guide for more information.

Installation

Confirm machine power is disconnected before beginning installation!

Use caution and appropriate protection to prevent hand and eye injury during installation!

Step 1 - Install Mounting Bracket

C-0935
Mounting Bracket

  1. Insert the C-0935 Mounting Bracket into the control panel.
    1. Secure with existing machine hardware.

Step 2 - Connect Power

C-5101C-5210C-5500C-5602
Spade Taps
Power Adapter Harness
Power Extension Harness
Power Converter

  1. Tap power as described in the Fascard Reader Install - Universal Concepts document using the C-5101 Spade Taps provided.
  2. Connect the C-5210 Power Adapter Harness to the installed spade taps. Connect the opposite end to the C-5602 Power Converter.
  3. Connect the C-5500 Power Extension Harness to the appropriate connector on the C-5602 Power Converter. The remaining cable end connects to the FasCard reader.

Step 3 - Connect Machine Start Harness

C-0122C-5305
Spade Taps
Machine Start Harness

  1. Disconnect the two coin drop wires from the pre-existing card reader.
  2. Tap the two coin drop wires using C-0122 Spade Taps.
  3. Connect the C-5305 Machine Start Harness to the Spade Taps.

Step 4 - Connect and Mount FasCard Reader

C-0141C-5305C-5500
Screw
Machine Start Harness
Power Extension Harness

  1. Feed remaining harness ends through mounting hole as described in FasCard Mounting Guide.
  2. Connect the free end of the C-5305 Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.
  3. Connect the free end of the C-5500 Power Extension Harness to port 4 (C-5500 Power Harness Connection Port) as shown in the image above.
  4. Connect FasCard reader to Mounting Bracket using the C-0141 Screws.
  5. Program the card reader address as described here: How to Program Address on a FasCard Reader.

Associated Equipment Models

MakeModelPulse LengthSensorControlNotes
Speed QueenSC##BY########-80FalseSingle-Vend (Pulse)Notes