Page tree
Skip to end of metadata
Go to start of metadata

On this Page

Overview and Equipment Information

This document is intended to guide the user through installation utilizing the kit numbered according to the document title. A list of associated equipment models including control information and additional installation notes can be found below.

Kit Installation Notes

Status: Active

Product: FasCard F1
Manufacturer: Alliance
Start Harness: 3-pin (1x3) molex connector
Interface Type: Pulse
Install Type: Coin and Card
Actuation: Coin Drop - Factory
Coin Sense: N/A
Mounting: Surface Mount
Chassis: N/A
Readers: 2 Readers
Machine Control: N/A


This document assumes the installer has working knowledge of hand tools and of the target machine in question. Physical modification of machine may be required, including modification of machine panels and internal modification to accommodate cables or harnesses. It is recommended that the instructions contained herein be performed by individuals who are qualified to perform these tasks. Card Concepts Inc. takes no responsibility for the accuracy of this document or for any damage that may occur to target machine.

Required Hardware

Card Reader

Part IDDescriptionImage
C-5001
F1 FasCard Reader

Installation Kit

QTYPart NumberDescriptionImage
2C-5250Coin Sense Harness
2C-5300-NCMachine Start Harness
2C-5801F1 Reader Mounting Kit
2C-6204Power Adapter Harness

Recommended Tools and Supplies (Not Included)

See FasCard Mounting Guide for more information.

Installation

Confirm machine power is disconnected before beginning installation!

Use caution and appropriate protection to prevent hand and eye injury during installation!

Step 1 - Install Mounting Brackets

C-5700-TEMPC-5801
Drill Template
F1 Reader Mounting Kit

  1. Place the C-5700-TEMP Drill Template on the desired mounting locations.
  2. Verify included harnesses will reach desired locations without encountering interference from internal machine components.
  3. Refer to FasCard Mounting Guide for further instructions.

Step 2 - Connect Power

C-6204
Power Adapter Harness

  1. Connect the C-6204 12VDC Power Harness to the H10 Connection on the Machine Control Assembly.
    1. Connect the green wire to a chassis ground.
  2. The remaining end (3-pin molex) connects directly to the rear of the F2 FasCard Reader.
  3. Repeat for second control.

Step 3 - Connect Coin Sense Harness

C-5250
Coin Sense Harness

  1. Disconnect the Coin Drops from the Machine Control Assemblies.
  2. Connect the C-5250 Coin Sense Harnesses to the harnesses connected to the Coin Drops.

Step 4 - Connect Machine Start Harness

C-5300-NC
Machine Start Harness

  1. Connect the C-5300-NC Machine Start Harnesses to the Machine Control Assemblies.

Step 5 - Connect and Mount FasCard Reader

C-5250C-5300-NCC-6204
Coin Sense Harness
Machine Start Harness
Power Adapter Harness

  1. Feed remaining harness ends through mounting hole as described in FasCard Mounting Guide.
  2. Connect the free end of the C-5300-NC Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.
  3. Connect the free end of the C-5250 Coin Sense Harness to port 3 (Coin Sense Harness Connection Port) as shown in the image above.
  4. Connect the C-6204 to port 4 (C-5500 Power Harness Connection Port) as shown in the image above.
  5. Connect FasCard reader to base as described in the FasCard Mounting Guide.
  6. Program the card reader address as described here: How to Program Address on a FasCard Reader.

Associated Equipment Models

MakeModelPulse LengthSensorControlNotes
ContinentalKTT###B?########-80FalseSingle-Vend (Pulse)
HuebschHTT###B###########-80FalseSingle-Vend (Pulse)
HuebschHTT??#WCA#########?FalseSingle-Vend (Pulse)
Speed QueenSTT###B###########-80FalseSingle-Vend (Pulse)