Page tree
Skip to end of metadata
Go to start of metadata

On this Page

Overview and Equipment Information

This document is intended to guide the user through installation utilizing the kit numbered according to the document title. A list of associated equipment models including control information and additional installation notes can be found below.

Kit Installation Notes

Status: Active

Product: FasCard F1
Manufacturer: ADC
Start Harness: 3-pin (1x3) molex connector
Interface Type: Pulse
Install Type: Card Only
Actuation: Coin Drop - Factory
Coin Sense: N/A
Mounting: Custom Bracket
Chassis: Large Chassis
Readers: 1 Reader
Machine Control: ADC Phase 7


Technical Support recommends reviewing the following additional configuration information before installation: LG Giant-C Washer Configuration.

This document assumes the installer has working knowledge of hand tools and of the target machine in question. Physical modification of machine may be required, including modification of machine panels and internal modification to accommodate cables or harnesses. It is recommended that the instructions contained herein be performed by individuals who are qualified to perform these tasks. Card Concepts Inc. takes no responsibility for the accuracy of this document or for any damage that may occur to target machine.

Required Hardware

Card Reader

Part IDDescriptionImage
C-5001
F1 FasCard Reader

This installation also requires a Greenwald Coin Interface harness, included with Coin Ready machines.  If this component is absent, it may be necessary to contact a Greenwald distributor for assistance.

Installation Kit

QTYPart NumberDescriptionImage
2C-0141Screw
2C-0144Screw
1C-0930Mounting Bracket
1C-5021Label
1C-5027Label
3C-5101Spade Taps
1C-5210Power Adapter Harness
1C-5345Machine Start Harness
1C-5500-60Power Extension Harness
1C-5602Power Converter
1C-5700Mounting Bracket
1C-5702Chase Nipple
1C-5703Lock Nut
1C-6701Adapter Plate

Recommended Tools and Supplies (Not Included)

See F1 Reader Mounting Guide for more information.

Installation

Confirm machine power is disconnected before beginning installation!

Use caution and appropriate protection to prevent hand and eye injury during installation!

Step 1 - Install Mounting Bracket

C-0144C-0930C-5700C-5702C-5703C-6701
Screw
Mounting Bracket
Mounting Bracket
Chase Nipple
Lock Nut
Adapter Plate

  1. Attach the C-5700 Surface Mounting Bracket to the C-6701 Adapter Plate using C-5702 Chase Nipple and C-5703 Nut.
    1. Make sure to orient the bracket so the two mounting holes on the C-6701 Adapter Plate are accessible (Fig 1).
  2. Place the newly assembled component on the outside of the machine, and place the C-0930 Mounting Bracket on the inside.
  3. Use the C-0144 Screws to attack the C-0930 Mounting Bracket to the outer components.

Fig. 1Fig. 2

Step 2 - Connect Power

C-5101C-5210C-5500-60C-5602
Spade Taps
Power Adapter Harness
Power Extension Harness
Power Converter

  1. Tap power as described in the Fascard Reader Install - Universal Concepts document using the C-5101 Spade Taps provided.
  2. Connect the C-5210 Power Adapter Harness to the installed spade taps. Connect the opposite end to the C-5602 Power Converter.
  3. Connect the C-5500-60 Power Extension Harness to the appropriate connector on the C-5602 Power Converter. The remaining cable end connects to the FasCard reader.

Step 3 - Connect Machine Start Harness

C-5345
Machine Start Harness

  1. Connect the C-5345 Machine Start Harness to the Coin Input Connection on the Machine Control Assembly.

Step 4 - Connect and Mount FasCard Reader

C-5345C-5500-60
Machine Start Harness
Power Extension Harness

  1. Feed remaining harness ends through mounting hole as described in F1 Reader Mounting Guide.
  2. Connect the free end of the C-5345 Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.
  3. Connect the free end of the C-5500-60 Power Extension Harness to port 4 (C-5500 Power Harness Connection Port) as shown in the image above.
  4. Connect FasCard reader to base as described in the FasCard Mounting Guide.
  5. Program the card reader address as described here: How to Program Address on a FasCard Reader.

Associated Equipment Models

MakeModelPulse LengthSensorControlNotes
ADCAD-758V60FalseSingle-Vend (Pulse)