Page tree
Skip to end of metadata
Go to start of metadata

On this Page

Overview and Equipment Information

This document is intended to guide the user through installation utilizing the kit numbered according to the document title. A list of associated equipment models including control information and additional installation notes can be found below.

Kit Installation Notes

Status: Active

Product: FasCard F2
Manufacturer: Alliance
Start Harness: 2-wire w/tap connections
Interface Type: Pulse
Install Type: Coin and Card
Actuation: Coin Drop - Factory
Coin Sense: Micro Switch
Mounting: Surface Mount
Chassis: N/A
Readers: 1 Reader
Machine Control: N/A

This document assumes the installer has working knowledge of hand tools and of the target machine in question. Physical modification of machine may be required, including modification of machine panels and internal modification to accommodate cables or harnesses. It is recommended that the instructions contained herein be performed by individuals who are qualified to perform these tasks. Card Concepts Inc. takes no responsibility for the accuracy of this document or for any damage that may occur to target machine.

Required Hardware

Card Reader

One of the following readers.

Part IDDescriptionImage
LC WiFi Reader
Front/Vertical Mount
LC WiFi Reader
Top/Horizontal Mount
F2 FasCard Reader
Front Mount
F2 FasCard Reader
High Front/Top Mount
FLEX Reader
Front/Vertical Mount
FLEX Reader
Top/Horizontal Mount

Installation Kit

QTYPart NumberDescriptionImage
1C-5256Machine Start Harns (pulse)
1C-5338Power Adapter Harness
1C-5500Power Extension Harness
1C-5602Power Converter
1C-6253Coin Sense Harness
1C-6801F2 Reader Mounting Kit

Recommended Tools and Supplies (Not Included)

See F2 Reader Mounting Guide for more information.


Confirm machine power is disconnected before beginning installation!

Use caution and appropriate protection to prevent hand and eye injury during installation!

Step 1 - Install Mounting Bracket

Drill Template
F2 Reader Mounting Kit

  1. Place the C-6700-TEMP Drill Template on the desired mounting location.
  2. Verify included harnesses will reach desired location without encountering interference from internal machine components.
  3. Refer to F2 Reader Mounting Guide for further instructions.

Step 2 - Connect Power

Power Adapter Harness
Power Extension Harness
Power Converter

  1. Tap power as described in the Fascard Reader Install - Universal Concepts document by connecting the C-5338 Power Adapter Harness to the power distribution panel inside the machine or tapping as needed.
    1. 120vac- Connect Brown and Blue wires to connector #2 closest to outside of machine and #4 on terminal side closest to circuit board.
    2. 240vac- Connect Brown and Blue wires to connectors 3 and 5 on the terminal side closest to the circuit board.
    3. Secure the green wire beneath the ground screw.
  2. Connect the opposite end of the C-5338 Power Adapter Harness to the C-5602 Power Converter.
  3. Connect the C-5500 Power Extension Harness to the appropriate connector on the C-5602 Power Converter. The remaining cable end connects to the FasCard reader.

Step 3 - Connect Coin Sense Harness

Coin Sense Harness

  1. Disconnect the Coin Drop from the Machine Control Assembly.
  2. Connect the C-6253 Coin Sense Harness to the Coin Drop.

Step 4 - Connect Machine Start Harness

Machine Start Harns (pulse)

  1. Connect the C-5256 Machine Start Harness to the harness that was previously connected to the Coin Drop.

Step 5 - Connect and Mount FasCard Reader

Machine Start Harns (pulse)
Power Extension Harness
Coin Sense Harness

  1. Feed remaining harness ends through mounting hole as described in F2 Reader Mounting Guide.
  2. Connect the free end of the C-5256 Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image below.
  3. Connect the free end of the C-6253 Coin Sense Harness to port 3 (Coin 1 Connection Port) as shown in the image below.
  4. Connect the free end of the C-5500 Power Extension Harness to port 4 (C-5500 Power Harness Connection Port) as shown in the image below.
  5. Connect FasCard reader to base as described in the F2 Reader Mounting Guide.
  6. Program the card reader address as described here: How to Program Address on a FasCard Reader.

Item No.ComponentNotes
1Power Connection PortUtilizes the same power harnesses as the first generation FasCard reader.
2Pulse Connection PortConnection point for pulse machine start harnesses.
3Coin 1 Connection PortThis is the connection point for the harness input associated with Coin 1.
4Coin 2 Connection PortThis is the connection point for the harness input associated with Coin 2.
5Serial Connection PortThis is the connection point for serial machine start harnesses.

Associated Equipment Models

MakeModelPulse LengthSensorControlNotes
DexterEX325*?FalseSingle-Vend (Pulse)Notes
DexterEX440*?FalseSingle-Vend (Pulse)Notes
DexterWCH18AA150FalseSingle-Vend (Pulse)
DexterWCH18AB150FalseSingle-Vend (Pulse)
DexterWCK#A#55FalseSingle-Vend (Pulse)
DexterWCK55AEK150FalseSingle-Vend (Pulse)
DexterWCK6ABSS150FalseSingle-Vend (Pulse)
DexterWCL25AB150FalseSingle-Vend (Pulse)
DexterWCN##AA##150FalseSingle-Vend (Pulse)
DexterWCN##AB##150FalseSingle-Vend (Pulse)Notes
DexterWCN##AEK150FalseSingle-Vend (Pulse)Notes
Speed QueenEX325*?FalseSingle-Vend (Pulse)Notes
Speed QueenEX440*?FalseSingle-Vend (Pulse)Notes
Speed QueenSTD32DG-43FalseSingle-Vend (Pulse)