Page tree
Skip to end of metadata
Go to start of metadata

On this Page

Overview and Equipment Information

This document is intended to guide the user through installation utilizing the kit numbered according to the document title. A list of associated equipment models including control information and additional installation notes can be found below.

Kit Installation Notes

Status: Active

Product: FasCard F2 [Stack Add-On]
Manufacturer: Alliance
Start Harness: 2-wire w/tap connections
Interface Type: Pulse
Install Type: Coin and Card
Actuation: Coin Drop - Factory
Coin Sense: Micro Switch
Mounting: Surface Mount
Chassis: N/A
Readers: 1 Reader
Machine Control: N/A


This document assumes the installer has working knowledge of hand tools and of the target machine in question. Physical modification of machine may be required, including modification of machine panels and internal modification to accommodate cables or harnesses. It is recommended that the instructions contained herein be performed by individuals who are qualified to perform these tasks. Card Concepts Inc. takes no responsibility for the accuracy of this document or for any damage that may occur to target machine.

Required Hardware

Card Reader

One of the following readers.

Part IDDescriptionImage
C-3001
LC WiFi Reader
Front/Vertical Mount
C-3002
LC WiFi Reader
Top/Horizontal Mount
C-5401
F2 FasCard Reader
Front Mount
C-5402
F2 FasCard Reader
High Front/Top Mount
C-5403
FLEX Reader
Front/Vertical Mount
C-5404
FLEX Reader
Top/Horizontal Mount

Installation Kit

QTYPart NumberDescriptionImage
1C-5256-120Machine Start Harness
1C-6253-120Coin Sense Harness
1C-6400F2, Stack Add On Board - SLV

Recommended Tools and Supplies (Not Included)

See F2 Reader Mounting Guide for more information.

Installation

Confirm machine power is disconnected before beginning installation!

Use caution and appropriate protection to prevent hand and eye injury during installation!

Step 1 - Install Mounting Bracket

C-6700-TEMPC-6801
Drill Template
F2 Reader Mounting Kit

  1. Place the C-6700-TEMP Drill Template on the desired mounting location.
  2. Verify included harnesses will reach desired location without encountering interference from internal machine components.
  3. Refer to F2 Reader Mounting Guide for further instructions.

Step 2 - Connect Power

C-5338C-5500C-5602
Power Adapter Harness
Power Extension Harness
Power Converter

  1. Tap power as described in the Fascard Reader Install - Universal Concepts document by connecting the C-5338 Power Adapter Harness to the power distribution panel inside the machine or tapping as needed.
    1. 120vac- Connect Brown and Blue wires to connector #2 closest to outside of machine and #4 on terminal side closest to circuit board.
    2. 240vac- Connect Brown and Blue wires to connectors 3 and 5 on the terminal side closest to the circuit board.
    3. Secure the green wire beneath the ground screw.
  2. Connect the opposite end of the C-5338 Power Adapter Harness to the C-5602 Power Converter.
  3. Connect the C-5500 Power Extension Harness to the appropriate connector on the C-5602 Power Converter. The remaining cable end connects to the FasCard reader.

Step 3 - Connect Coin Sense Harness

C-6253C-6253-120
Coin Sense Harness
Coin Sense Harness

  1. Disconnect the Coin Drop from the Machine Control Assembly for both the upper and lower pockets.
  2. Connect the C-6253 Coin Sense Harness to the Coin Drop associated with the upper pocket.
  3. Connect the C-6253-120 Coin Sense Harness to the Coin Drop associated with the lower pocket.

Step 4 - Connect Machine Start Harness

C-5256C-5256-120
Machine Start Harns (pulse)
Machine Start Harness

  1. Connect the C-5256 Machine Start Harness to the harness that was previously connected to the upper pocket's Coin Drop.
  2. Connect the C-5256-120 Machine Start Harness to the harness that was previously connected to the lower pocket's Coin Drop.

Step 5 - Connect and Mount FasCard Reader

C-5256C-5256-120C-5500C-6253C-6253-120
Machine Start Harns (pulse)
Machine Start Harness
Power Extension Harness
Coin Sense Harness
Coin Sense Harness

  1. Feed remaining harness ends through mounting hole as described in F2 Reader Mounting Guide.
  2. Connect the free end of the C-5256 Machine Start Harness to port 2 (Upper Pulse Connection Port) as shown in the image below.
  3. Connect the free end of the C-5256-120 Machine Start Harness to port 10 (Lower Pulse Connection Port) as shown in the image below.
  4. Connect the free end of the C-6253 Coin Sense Harness to port 3 (Coin 1 Connection Port) as shown in the image below.
  5. Connect the free end of the C-6253-120 Coin Sense Harness to port 4 (Coin 2 Connection Port) as shown in the image below.
  6. Connect the free end of the C-5500 Power Extension Harness to port 1 (C-5500 Power Harness Connection Port) as shown in the image below.
  7. Connect FasCard reader to base as described in the F2 Reader Mounting Guide.
  8. Program the card reader address as described here: How to Program Address on a FasCard Reader.


Associated Equipment Models

MakeModelPulse LengthSensorControlNotes
Speed QueenSTD32DG-43FalseSingle-Vend (Pulse)