Page tree
Skip to end of metadata
Go to start of metadata

On this Page

Overview and Equipment Information

This document is intended to guide the user through installation utilizing the kit numbered according to the document title. A list of associated equipment models including control information and additional installation notes can be found below.

Kit Installation Notes

Status: Active

Product: FasCard F2 [Stack Add-On]
Manufacturer: Continental
Start Harness: 3-pin (1x3) molex connector
Interface Type: Pulse
Install Type: Coin and Card
Actuation: Coin Drop - Factory
Coin Sense: N/A
Mounting: Surface Mount
Chassis: N/A
Readers: 1 Reader
Machine Control: N/A


This document assumes the installer has working knowledge of hand tools and of the target machine in question. Physical modification of machine may be required, including modification of machine panels and internal modification to accommodate cables or harnesses. It is recommended that the instructions contained herein be performed by individuals who are qualified to perform these tasks. Card Concepts Inc. takes no responsibility for the accuracy of this document or for any damage that may occur to target machine.

Required Hardware

Card Reader

One of the following readers.

Part IDDescriptionImage
C-3001
LC WiFi Reader
Front/Vertical Mount
C-3002
LC WiFi Reader
Top/Horizontal Mount
C-5401
F2 FasCard Reader
Front Mount
C-5402
F2 FasCard Reader
High Front/Top Mount
C-5403
FLEX Reader
Front/Vertical Mount
C-5404
FLEX Reader
Top/Horizontal Mount

Installation Kit

QTYPart NumberDescriptionImage
1C-5300-NC-144Machine Start Harness
1C-6250-144Coin Sense Harness
1C-6400F2, Stack Add On Board - SLV

Recommended Tools and Supplies (Not Included)

DescriptionLink/SourceImage
Steel Fish TapeAmazon


See F2 FasCard Mounting Guide for more information.

Installation

Confirm machine power is disconnected before beginning installation!

Use caution and appropriate protection to prevent hand and eye injury during installation!

Step 1 - Machine Prep

  1. Remove control boards from the machine.
  2. Open firewall panel behind control boards on each side by removing the 4 screws. (Fig. 1)
  3. Drill a 1-1/8" using a hole saw in the upper portion of the firewall on each side. (Fig. 2)
    1. Use caution to avoid damaging anything behind the firewall.

Fig. 1Fig. 2


Step 2 - Install Secondary Start and Coin Sense Harness

C-5300-NC-144C-6250-144
Machine Start Harness
Coin Sense Harness

  1. From the side where the F2 card reader is mounted, run the C-6250-144 Coin Sense Harness and C-5300-NC-144 Machine Start Harness through the hole in the firewall.
    1. Ensure the white, 3-pin connector ends are run to the secondary control board.
  2. Using the fish tape, run the wires to the secondary control panel following the existing dryer cables that run above the lint drawer and below the cylinder shroud behind the firewall. (Fig. 3)
  3. Disconnect the Coin Drop from the Machine Control Assembly and connect the C-6250-144 Coin Sense Harness to the Coin Drop.
  4. Connect the C-5300-NC-144 Machine Start Harness to where the Coin Drop was previously connected on the Machine Control Assembly.
  5. Loop and secure any excess lengths of the Coin Sense Harness and Machine Start Harness to ensure they are not damaged.

Fig. 3

Step 3 - Connect and Mount FasCard Reader

C-5300-NCC-5300-NC-144C-6208C-6250C-6250-144C-6400
Machine Start Harness
Machine Start Harness
F2, Power Adapter Harness
Coin Sense Harness
Coin Sense Harness
F2, Stack Add On Board - SLV

  1. Feed remaining harness ends through mounting hole as described in F2 FasCard Mounting Guide.
  2. Connect the C-6400 Stack Add-on Board to port 5 (Serial Connection Port) as shown in the image above.
  3. Connect the free end of the C-5300-NC Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.
  4. Connect the free end of the C-6250 Coin Sense Harness to port 3 (Coin Sense Harness Connection Port) as shown in the image above.
  5. Connect the free end of the C-6250-144 Coin Sense Harness to port 4 (Coin Sense Harness Connection Port) as shown in the image above.
  6. Connect the free end of the C-5300-NC-144 Machine Start Harness to port 10 (Pulse Connection Port) on the C-6400 Stack Add-on Board as shown in the image above.
  7. Connect the free end of the C-6208 Power Extension Harness to port 1 (C-5500 Power Harness Connection Port) as shown in the image above.
  8. Connect FasCard reader to base as described in the F2 FasCard Mounting Guide.
  9. Program the card reader address as described here: How to Program Address on a FasCard Reader.

Associated Equipment Models

MakeModelPulse LengthSensorControlNotes
ContinentalKTT###B?#######?FalseSingle-Vend (Pulse)
ContinentalKTT###N########45FalseSingle-Vend (Pulse)
HuebschHTT###BC#######-100FalseSingle-Vend (Pulse)
Speed QueenSTT###B?#######-80FalseSingle-Vend (Pulse)