Page tree
Skip to end of metadata
Go to start of metadata

On this Page

Overview and Equipment Information

This document is intended to guide the user through installation utilizing the kit numbered according to the document title. A list of associated equipment models including control information and additional installation notes can be found below.

Kit Installation Notes

Status: Retired

Product: FasCard F2
Manufacturer: Alliance
Start Harness: 7-pin single row flat connector
Interface Type: Serial
Install Type: Card Only
Actuation: Card Ready
Coin Sense: N/A
Mounting: Custom Bracket
Chassis: N/A
Readers: 1 Reader
Machine Control: Alliance MDC/Centurion

This document assumes the installer has working knowledge of hand tools and of the target machine in question. Physical modification of machine may be required, including modification of machine panels and internal modification to accommodate cables or harnesses. It is recommended that the instructions contained herein be performed by individuals who are qualified to perform these tasks. Card Concepts Inc. takes no responsibility for the accuracy of this document or for any damage that may occur to target machine.

Required Hardware

Card Reader

One of the following readers.

Part IDDescriptionImage
LC WiFi Reader
Front/Vertical Mount
LC WiFi Reader
Top/Horizontal Mount
F2 FasCard Reader
Front Mount
F2 FasCard Reader
High Front/Top Mount
FLEX Reader
Front/Vertical Mount
FLEX Reader
Top/Horizontal Mount

Installation Kit

QTYPart NumberDescriptionImage
1C-0110-CPJumper Plug
1C-0110-TOPMachine Start Harness
2C-1060Screw - Build: TK
2C-5101Spade Taps
1C-5414F2 Standard Mounting Bracket
1C-5710Rubber Grommet
1C-6208F2, Power Adapter Harness
1C-6970F2, Bracket

Recommended Tools and Supplies (Not Included)

See F2 FasCard Mounting Guide for more information.


Confirm machine power is disconnected before beginning installation!

Use caution and appropriate protection to prevent hand and eye injury during installation!

Step 1 - Install Mounting Bracket

Screw - Build: TK
F2 Standard Mounting Bracket
F2, Bracket

  1. Install the C-6970 Bracket on the control panel.
  2. Attach the C-5414 F2 Mounting Bracket onto the C-6970 Bracket using the C-1060 Screws.

Step 2 - Connect Power

Spade Taps
F2, Power Adapter Harness

  1. Tap power as described in the Fascard Reader Install - Universal Concepts document using the C-5101 Spade Taps provided.
    1. Tap the 24vac lines toward the front of the machine, closest to the reader mounting location.
  2. Connect the C-6208 Power Adapter Harness to the installed spade taps. The remaining cable end connects to the FasCard reader after installation.

Step 3 - Connect Machine Start Harness

Jumper Plug
Machine Start Harness

  1. Connect the C-0110-CP Jumper Plug to the Machine Control Assembly.
    1. It may be necessary to remove the existing Alliance Jumper Plug before installing C-0110-CP Jumper Plug.
  2. Connect the C-0110-TOP Machine Start Harness to the Machine Control Assembly serial interface port.

Step 4 - Connect and Mount FasCard Reader

Machine Start Harness
F2, Power Adapter Harness

Item No.ComponentNotes
1Power Connection PortUtilizes the same power harnesses as the first generation FasCard reader.
2Pulse Connection PortConnection point for pulse machine start harnesses.
3Coin 1 Connection PortThis is the connection point for the harness input associated with Coin 1.
4Coin 2 Connection PortThis is the connection point for the harness input associated with Coin 2.
5Serial Connection PortThis is the connection point for serial machine start harnesses.

  1. Feed remaining harness ends through mounting hole as described in F2 FasCard Mounting Guide.
  2. Connect the free end of the C-0110-TOP Machine Start Harness to port 5 (Serial Connection Port) as shown in the image above.
  3. Connect the free end of the C-6208 Power Adapter Harness to port 1 (C-5500 Power Harness Connection Port) as shown in the image above.
  4. Connect FasCard reader to base as described in the F2 FasCard Mounting Guide.
  5. Program the card reader address as described here: How to Program Address on a FasCard Reader.

Associated Equipment Models