Page tree
Skip to end of metadata
Go to start of metadata

On this Page

Overview and Equipment Information

This document is intended to guide the user through installation utilizing the kit numbered according to the document title. A list of associated equipment models including control information and additional installation notes can be found below.

Kit Installation Notes

Status: Active

Product: FasCard F2
Manufacturer: Laundrylux
Start Harness: 6-pin (2x3) molex connector
Interface Type: Pulse
Install Type: Card Only
Actuation: Coin Drop - Factory
Coin Sense: N/A
Mounting: Custom Bracket
Chassis: N/A
Readers: 1 Reader
Machine Control: N/A


This document assumes the installer has working knowledge of hand tools and of the target machine in question. Physical modification of machine may be required, including modification of machine panels and internal modification to accommodate cables or harnesses. It is recommended that the instructions contained herein be performed by individuals who are qualified to perform these tasks. Card Concepts Inc. takes no responsibility for the accuracy of this document or for any damage that may occur to target machine.

Required Hardware

Card Reader

One of the following readers.

Part IDDescriptionImage
C-3001
LC WiFi Reader
Front/Vertical Mount
C-3002
LC WiFi Reader
Top/Horizontal Mount
C-5401
F2 FasCard Reader
Front Mount
C-5402
F2 FasCard Reader
High Front/Top Mount
C-5403
FLEX Reader
Front/Vertical Mount
C-5404
FLEX Reader
Top/Horizontal Mount

Installation Kit

QTYPart NumberDescriptionImage
2C-1059Nut
3C-5101Spade Taps
1C-5210Power Adapter Harness
1C-5380Combination Harness
1C-5500Power Extension Harness
1C-5602Power Converter
1C-6801F2 Reader Mounting Kit
1C-6920R1Mounting Bracket

Recommended Tools and Supplies (Not Included)

See F2 FasCard Mounting Guide for more information.

Installation

Confirm machine power is disconnected before beginning installation!

Use caution and appropriate protection to prevent hand and eye injury during installation!

Step 1 - Install Mounting Bracket

C-1059C-6801C-6920R1
Nut
F2 Reader Mounting Kit
Mounting Bracket

  1. Remove the existing Coin Drop.
    1. Refer to manufacturer documentation as needed.
  2. Insert the C-6920R1 Mounting Bracket into the Coin Vault and secure using the C-1059 Kep Nuts.
  3. Secure the C-5414 F2 Mounting Bracket to the C-6920R1 Mounting Bracket using the C-5702 Chase Nipple and C-5703 Nut.

Step 2 - Connect Machine Start Harness

C-5380
Combination Harness

  1. Disconnect the Coin Drop from the Machine Control Assembly.
  2. Connect C-5380 Combination Harness to the machine where the Coin Drop was previously connected.
    1. The 6 pin 2x3 female connector will not be connected to anything as the Coin Drop will not be used.

Step 3 - Connect Power

C-5101C-5210C-5500C-5602
Spade Taps
Power Adapter Harness
Power Extension Harness
Power Converter

  1. Tap power as described in the Fascard Reader Install - Universal Concepts document using the C-5101 Spade Taps provided.
  2. Connect the C-5210 Power Adapter Harness to the installed spade taps. Connect the opposite end to the C-5602 Power Converter.
  3. Connect the C-5500 Power Extension Harness to the appropriate connector on the C-5602 Power Converter. The remaining cable end connects to the FasCard reader.

Step 5 - Final Connections

C-5380C-5500
Combination Harness
Power Extension Harness

Item No.ComponentNotes
1Power Connection PortUtilizes the same power harnesses as the first generation FasCard reader.
2Pulse Connection PortConnection point for pulse machine start harnesses.
3Coin 1 Connection PortThis is the connection point for the harness input associated with Coin 1.
4Coin 2 Connection PortThis is the connection point for the harness input associated with Coin 2.
5Serial Connection PortThis is the connection point for serial machine start harnesses.

  1. Feed remaining harness ends through mounting bracket.
  2. Connect the free end of the C-5380 Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.
  3. Connect the free end of the C-5500 Power Extension Harness to port 1 (C-5500 Power Harness Connection Port) as shown in the image above.
  4. The small, black 5 pin connector will not be connected as the Coin Drop is not being used.
  5. Connect FasCard reader to base as described in the F2 FasCard Mounting Guide.
  6. Program the card reader address as described here: How to Program Address on a FasCard Reader.