Page tree
Skip to end of metadata
Go to start of metadata

On this Page

Overview and Equipment Information

This document is intended to guide the user through installation utilizing the kit numbered according to the document title. A list of associated equipment models including control information and additional installation notes can be found below.

Kit Installation Notes

Status: Retired

Product: FasCard F2
Manufacturer: Laundrylux
Start Harness: 8-pin single row flat connector
Interface Type: Serial
Install Type: Coin and Card
Actuation: Coin Drop - Factory
Coin Sense: N/A
Mounting: Surface Mount
Chassis: N/A
Readers: 1 Reader
Machine Control: Laundrylux Crossover


This document assumes the installer has working knowledge of hand tools and of the target machine in question. Physical modification of machine may be required, including modification of machine panels and internal modification to accommodate cables or harnesses. It is recommended that the instructions contained herein be performed by individuals who are qualified to perform these tasks. Card Concepts Inc. takes no responsibility for the accuracy of this document or for any damage that may occur to target machine.

Required Hardware

Card Reader

One of the following readers.

Part IDDescriptionImage
C-3001
LC WiFi Reader
Front/Vertical Mount
C-3002
LC WiFi Reader
Top/Horizontal Mount
C-5401
F2 FasCard Reader
Front Mount
C-5402
F2 FasCard Reader
High Front/Top Mount
C-5403
FLEX Reader
Front/Vertical Mount
C-5404
FLEX Reader
Top/Horizontal Mount

Installation Kit

QTYPart NumberDescriptionImage
1C-5350Power Adapter Harness
1C-5355Machine Start Harness
1C-6352Coin Sense Harness
1C-6800F2 Reader Mounting Kit

Recommended Tools and Supplies (Not Included)

See F2 Reader Mounting Guide for more information.

Installation

Confirm machine power is disconnected before beginning installation!

Use caution and appropriate protection to prevent hand and eye injury during installation!

Step 1 - Install Mounting Bracket

C-6700-TEMPC-6800
Drill Template
F2 Reader Mounting Kit

  1. Place the C-6700-TEMP Drill Template on the desired mounting location.
  2. Verify included harnesses will reach desired location without encountering interference from internal machine components.
  3. Refer to F2 Reader Mounting Guide for further instructions.

Step 2 - Connect Power

C-5350
Power Adapter Harness

  1. Connect the C-5350 Power Harness to the mated power harness inside the machine.
  2. Secure the ground wire terminal beneath a chassis screw.

Step 3 - Connect Coin Sense Harness

C-6352
Coin Sense Harness

  1. Disconnect the Coin Drop from the Machine Control Assembly.
  2. Connect the C-6352 Coin Sense Harness to the harness connected to the Coin Drop.

Step 4 - Connect Machine Start Harness

C-5355
Machine Start Harness

  1. Connect the C-5355 Machine Start Harness to the Machine Control Assembly ribbon cable.

Step 5 - Connect and Mount FasCard Reader

C-5350C-5355C-5402C-6352
Power Adapter Harness
Machine Start Harness
F2 FasCard Reader
Coin Sense Harness

  1. Feed remaining harness ends through mounting hole as described in F2 Reader Mounting Guide.
  2. Connect the free end of the C-5355 Machine Start Harness to port 5 (Serial Connection Port) as shown in the image below.
  3. Connect the free end of the C-6352 Coin Sense Harness to port 3 (Coin 1 Connection Port) as shown in the image below.
  4. Connect the free end of the C-5350 Power Adapter Harness to port 1 (Power Connection Port) as shown in the image below.
  5. Connect FasCard reader to base as described in the F2 Reader Mounting Guide.
  6. Program the card reader address as described here: How to Program Address on a FasCard Reader.

Item No.ComponentNotes
1Power Connection PortUtilizes the same power harnesses as the first generation FasCard reader.
2Pulse Connection PortConnection point for pulse machine start harnesses.
3Coin 1 Connection PortThis is the connection point for the harness input associated with Coin 1.
4Coin 2 Connection PortThis is the connection point for the harness input associated with Coin 2.
5Serial Connection PortThis is the connection point for serial machine start harnesses.

Associated Equipment Models