Page tree
Skip to end of metadata
Go to start of metadata

On this Page

Overview and Equipment Information

This document is intended to guide the user through installation utilizing the kit numbered according to the document title. A list of associated equipment models including control information and additional installation notes can be found below.

Kit Installation Notes

Status: Active

Product: FasCard F2
Manufacturer: Alliance
Start Harness: 3-pin (1x3) molex connector
Interface Type: Pulse
Install Type: Card Only
Actuation: Coin Drop - Factory
Coin Sense: N/A
Mounting: Coin Vault
Chassis: N/A
Readers: 1 Reader
Machine Control: Alliance MDC/Centurion

This document assumes the installer has working knowledge of hand tools and of the target machine in question. Physical modification of machine may be required, including modification of machine panels and internal modification to accommodate cables or harnesses. It is recommended that the instructions contained herein be performed by individuals who are qualified to perform these tasks. Card Concepts Inc. takes no responsibility for the accuracy of this document or for any damage that may occur to target machine.

Required Hardware

Card Reader

One of the following readers.

Part IDDescriptionImage
LC WiFi Reader
Front/Vertical Mount
LC WiFi Reader
Top/Horizontal Mount
F2 FasCard Reader
Front Mount
F2 FasCard Reader
High Front/Top Mount
FLEX Reader
Front/Vertical Mount
FLEX Reader
Top/Horizontal Mount

Installation Kit

QTYPart NumberDescriptionImage
2C-1070-WWasher - Build: XCH
1C-5300-NCMachine Start Harness
1C-5365Bypass Harness
1C-6204Power Adapter Harness
1C-6765-WF2 Mounting Bracket
1C-6801F2 Reader Mounting Kit

Recommended Tools and Supplies (Not Included)

See F2 FasCard Reader Mounting Guide for more information.


Confirm machine power is disconnected before beginning installation!

Use caution and appropriate protection to prevent hand and eye injury during installation!

Step 1 - Install Mounting Bracket

Washer - Build: XCH
F2 Mounting Bracket
F2 Reader Mounting Kit

  1. Remove the existing Coin Drop and Coin Box from the machine.
  2. Install the C-6765-W Mounting Bracket over the Coin Vault. Secure the Mounting Bracket using the C-1070-W Washers and C-1059 Nuts.
  3. Attach the C-5414 Standard Mounting Bracket to the C-6765-W Mounting Bracket using the C-5702 Chase Nipple and C-5703 Nut.

Step 2 - Connect Power

Power Adapter Harness

  1. Connect the C-6204 12VDC Power Harness to the H10 Connection on the Machine Control Assembly.
    1. Connect the green wire to a chassis ground.
  2. The remaining end (3-pin molex) connects directly to the rear of the F2 FasCard Reader.

Step 3 - Connect Machine Start Harness

Machine Start Harness
Bypass Harness

  1. Disconnect any existing Coin Drop.
  2. Connect the C-5300-NC Machine Start Harness to the harness previously connected to the Coin Drop.
  3. Disconnect the connections to the Coin Vault Switch and install the C-5365 Coin Vault Bypass to the existing harness connections.

Step 4 - Connect and Mount FasCard Reader

Machine Start Harness
F2 FasCard Reader
Power Adapter Harness

  1. Feed remaining harness ends through mounting hole as described in F2 FasCard Reader Mounting Guide.
  2. Connect the free end of the C-5300-NC Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image below.
  3. Connect the free end of the C-6204 Power Extension Harness to port 1 (Power Connection Port) as shown in the image below.
  4. Connect FasCard reader to base as described in the F2 FasCard Reader Mounting Guide.
  5. Program the card reader address as described here: How to Program Address on a FasCard Reader.

Item No.ComponentNotes
1Power Connection PortUtilizes the same power harnesses as the first generation FasCard reader.
2Pulse Connection PortConnection point for pulse machine start harnesses.
3Coin 1 Connection PortThis is the connection point for the harness input associated with Coin 1.
4Coin 2 Connection PortThis is the connection point for the harness input associated with Coin 2.
5Serial Connection PortThis is the connection point for serial machine start harnesses.

Associated Equipment Models

MakeModelPulse LengthSensorControlNotes
HuebschHF#K#A######N##?FalseSingle-Vend (Pulse)
Speed QueenSF#N#A####?#N01-80FalseSingle-Vend (Pulse)
Speed QueenSF#W?A####5#N01-80FalseSingle-Vend (Pulse)