Page tree
Skip to end of metadata
Go to start of metadata

On this Page

Overview and Equipment Information

This document is intended to guide the user through installation utilizing the kit numbered according to the document title. A list of associated equipment models including control information and additional installation notes can be found below.

Kit Installation Notes

Status: Active

Product: FasCard F2
Manufacturer: Alliance
Start Harness: 7-pin single row flat connector
Interface Type: Serial
Install Type: Card Only
Actuation: Coin Drop - Factory
Coin Sense: N/A
Mounting: Metercase Bracket
Chassis: N/A
Readers: 1 Reader
Machine Control: Alliance ACA


This document assumes the installer has working knowledge of hand tools and of the target machine in question. Physical modification of machine may be required, including modification of machine panels and internal modification to accommodate cables or harnesses. It is recommended that the instructions contained herein be performed by individuals who are qualified to perform these tasks. Card Concepts Inc. takes no responsibility for the accuracy of this document or for any damage that may occur to target machine.

Required Hardware

Card Reader

One of the following readers.

Part IDDescriptionImage
C-3001
LC WiFi Reader
Front/Vertical Mount
C-3002
LC WiFi Reader
Top/Horizontal Mount
C-5401
F2 FasCard Reader
Front Mount
C-5402
F2 FasCard Reader
High Front/Top Mount
C-5403
FLEX Reader
Front/Vertical Mount
C-5404
FLEX Reader
Top/Horizontal Mount

Installation Kit

QTYPart NumberDescriptionImage
2C-1059Nut
2C-1070-WWasher - Build: XCH
3C-5101Spade Taps
1C-5240Machine Start Harness
1C-5338Power Adapter Harness
1C-5500Power Extension Harness
1C-5602Power Converter
1C-5760-AAlliance Adapter Bracket
1C-6762Metercase Bracket
1C-6801F2 Reader Mounting Kit

Recommended Tools and Supplies (Not Included)

See F2 Reader Mounting Guide for more information.

Installation

Confirm machine power is disconnected before beginning installation!

Use caution and appropriate protection to prevent hand and eye injury during installation!

Step 1 - Install Mounting Bracket

C-1059C-1070-WC-5414C-5702C-5703C-5760-AC-6762
Nut
Washer - Build: XCH
F2 Standard Mounting Bracket
Chase Nipple
Lock Nut
Alliance Adapter Bracket
Metercase Bracket

  1. Remove any existing Coin Drop.
  2. Install the C-5414 Mounting Bracket onto the C-6762 Metercase Bracket using the C-5702 and C-5703 Chase Nipple and Nut.
  3. Install the C-5760-A Adapter Bracket onto the C-6762 Metercase Bracket.
  4. Install the C-6762 Metercase Bracket over the front of the Metercase and secure with C-1070-W Washer and C-1059 Nut.
  5. Refer to FasCard Mounting Guide for further information as needed.

Step 2 - Connect Power

C-5101C-5338C-5500C-5602
Spade Taps
Power Adapter Harness
Power Extension Harness
Power Converter

  1. Tap power as described in the Fascard Reader Install - Universal Concepts document using the C-5101 Spade Taps provided.
  2. Connect the C-5338 Power Adapter Harness to the installed spade taps and ground appropriately. Connect the opposite end to the C-5602 Power Converter.
  3. Connect the C-5500 Power Extension Harness to the appropriate connector on the C-5602 Power Converter. The remaining cable end connects to the FasCard reader.

Step 3 - Connect Machine Start Harness

C-5240
Machine Start Harness

  1. Connect the C-5240 Machine Start Harness to the H3 connection on the Machine Control Assembly.

Step 4 - Connect and Mount FasCard Reader

C-5240C-5401C-5500
Machine Start Harness
F2 FasCard Reader
Power Extension Harness

  1. Feed remaining harness ends through mounting hole as described in F2 Reader Mounting Guide.
  2. Connect the free end of the C-5240 Machine Start Harness to port 5 (Pulse Connection Port) as shown in the image below.
  3. Connect the free end of the C-5500 Power Extension Harness to port 1 (Power Connection Port) as shown in the image below.
  4. Connect FasCard reader to base as described in the F2 Reader Mounting Guide.
  5. Program the card reader address as described here: How to Program Address on a FasCard Reader.

Item No.ComponentNotes
1Power Connection PortUtilizes the same power harnesses as the first generation FasCard reader.
2Pulse Connection PortConnection point for pulse machine start harnesses.
3Coin 1 Connection PortThis is the connection point for the harness input associated with Coin 1.
4Coin 2 Connection PortThis is the connection point for the harness input associated with Coin 2.
5Serial Connection PortThis is the connection point for serial machine start harnesses.

Associated Equipment Models

MakeModelControlNotes
Speed QueenSD#N#R####3##02Alliance ACA H7S Small Dryer A4 - Quantum+
Speed QueenSW#NC2####3TW##Alliance ACA H7S Top Load Washer A4 - Quantum+