Skip to end of metadata
Go to start of metadata

Overview

Equipment Details


Average Installation Time


On This Page

Make: [VARIES]
TEST Reader Installation Guides


TODO


Known Models

HWFT71WN
HWFT73QN
HWFT73WN
SWFB73WN
SWFT611N
SWFT631N
SWFT711N
SWFT71WN
SWFT73WN
SWFX611N
SWFX731N
SWFY611N
SWFY61WN
SWFY711N
SWFY71WN
SWFY73WN
SWRB71WN
SWRT71WN
SWRT73*N
TEST Reader Installation Guides

This document assumes the installer has working knowledge of hand tools and of the target machine in question. Physical modification of machine may be required, including modification of machine panels and internal modification to accommodate cables or harnesses. It is recommended that the instructions contained herein be performed by individuals who are qualified to perform these tasks. Card Concepts Inc. takes no responsibility for the accuracy of this document or for any damage that may occur to target machine.

Required Hardware

Card Reader

Part IDDescriptionImage
C-0103-B
LaundryCard Reader V3 - RevB

Recommended Tools and Supplies (Not Included)

Installation

    Page not found for multiexcerpt macro.
The page: null was not found. Please check/update the page name used in the 'multiexcerpt-include' macro.

Install Mounting Hardware

Coin Ready Models

P/N: C-0015
Label
Reader Cover Label
Qty: 1
P/N: C-0035
Label
3-7/8" x 3-1/4"
Qty: 1
P/N: C-0131
Standoff
8-32" x 2-3/4" - Hex
Qty: 2
P/N: C-0140
Screw
8-32 x 3/4" - Cap
Qty: 2
P/N: C-0936
Vault Mount Bracket
Qty: 1
P/N: C-5365
Bypass Harness
Alliance Coin Vault Bypass
Qty: 1

  1. Remove existing coin box and coin drop.

  2. Place C-0035 Label over the coin drop opening.
  3. Remove connections from coin vault switch and bridge using C-5365 Bypass Harness.
  4. Bend the side tabs of the C-0936 Bracket outward and install into the coin vault. The tabs should snap into place securing the bracket.

  5. Attach the C-0131 Standoffs to the C-0936 Bracket.

Card Ready Models

P/N: C-0015
Label
Reader Cover Label
Qty: 1
P/N: C-0141
Screw
8-32 x 1-1/2" - Cap
Qty: 2
P/N: C-0970R1
Revised Mounting Bracket
Multi-Purpose
Qty: 1

  1. Use the C-0970R1 Mounting Bracket to mark the rectangular opening and the two screw holes directly the left and right of the rectangular opening.
  2. Cut out the rectangular opening and screw holes.
  3. After connecting the cables to the reader, insert the reader through the opening and place the C-0970R1 Mounting Bracket on the inside of the machine panel.
  4. Secure the reader to the C-0970R1 Mounting Bracket using the C-0141 Screws.

Connect Machine Interface Harness

Coin Pulse

P/N: C-0109R1
Machine Start Harness
Red / White w. Capacitor
Qty: 1

  1. Connect the C-0109R1 Machine Start Harness to the Coin 1 connector on the Machine Control Assembly.

Pulse - MDC / Quantum Gold Controls

P/N: C-0110-CP
Jumper Plug
Enables card mode on pre-ACA
Qty: 1
P/N: C-0110-TOP
Machine Start Harness
can use C-0110-TOP-144
Qty: 1

  1. Connect the C-0110-TOP Machine Start Harness to the H5 connection on the Machine Control Assembly.

Serial - MDC / Quantum Gold Controls

P/N: C-0110-CP
Jumper Plug
Enables card mode on pre-ACA
Qty: 1
P/N: C-0110-TOP
Machine Start Harness
can use C-0110-TOP-144
Qty: 1

  1. Connect the C-0110-TOP Machine Start Harness to the H5 connection on the Machine Control Assembly.
  2. Connect the C-0110-CP Jumper Plug to the H2 connection on the Machine Control Assembly.

Connect and Mount Reader

TODO - Include picture of LaundryCard reader connection

  1. Feed remaining harness ends through mounting bracket.
  2. Connect the free end of the Machine Start Harness:
    1. If following steps for a serial Machine Start Harness to port 1 (Serial Connection Port) as shown in the image above.
    2. If following steps for a pulse Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.
  3. Connect the the Cat5 cables running to and from the adjacent machines to ports labeled 3 (Line Connection Ports) as shown in the image above.
  4. Secure the LaundryCard reader to the bracket using included hardware.

Machine Configuration

TODO

LaundryCard Configuration

Use the following settings depending on the Machine Start Harness used.

Pulse (C-0110-TOP or C-0109R1)

  1. Equipment Type: SingleVend
  2. Pulse Length: 80

Serial (C-0110-TOP)

  1. Equipment Type: Alliance MDC Front Load Washer

    Page not found for multiexcerpt macro.
The page: null was not found. Please check/update the page name used in the 'multiexcerpt-include' macro.