Page tree

Versions Compared

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.
Div
Classtoc-header
Section
Column
width30
Panel
titleOn this Page

Table of Contents
maxLevel2
minLevel2

Column
width70
Panel
titleOverview and Equipment Information

Multiexcerpt include
MultiExcerptNameOverview
PageWithExcerptCCIDOC:_FC Reader Installation

Kit Installation Notes

Cci kits
TypeDescription

Multiexcerpt include
MultiExcerptNameF2 Install Header
DisableCachingtrue
PageWithExcerptCCIDOC:_FC Reader Installation

Installation Kit

Cci kits
TypeParts

Recommended Tools and Supplies (Not Included)

See F2 FasCard Reader Mounting Guide for more information.

Installation

Multiexcerpt include
MultiExcerptNamewarnings
DisableCachingtrue
PageWithExcerptCCIDOC:_LC Reader Installation

Div
Classinstall-steps
Panel

Step 1 - Install Mounting Bracket

Bw part list
PartsC-6700-Temp,C-6801
SizingModeHeight
ShowDesc2false
ShowDesc3false
SingleRowtrue

  1. Place the C-6700-TEMP Drill Template on the desired mounting location.
  2. Verify included harnesses will reach desired location without encountering interference from internal machine components.
  3. Refer to F2 FasCard Reader Mounting Guide for further instructions.
Panel

Step 2 - Connect Power

Bw part list
PartsC-6205
SizingModeHeight
ShowDesc2false
ShowDesc3false
SingleRowtrue

  1. Connect the C-6250 Power Adapter Harness to the machine 24vac power connector.
    1. Secure the ground wire to a screw located near the rear of the control pan.
    2. The remaining end of the harness connects directly to the FasCard reader.
Panel

Step 3 - Connect Coin Sense Harness

Bw part list
PartsC-6250
SizingModeHeight
ShowDesc2false
ShowDesc3false
SingleRowtrue

  1. Disconnect the Coin Drop from the Machine Control Assembly.
  2. Connect the C-6250 Coin Sense Harness to the harness connected to the Coin Drop.
Panel

Step 4 - Connect Machine Start Harness

Bw part list
PartsC-0110-CP,C-0110-TOP
SizingModeHeight
ShowDesc2false
ShowDesc3false
SingleRowtrue

  1. Remove the existing Alliance Jumper Plug at H8 and connect the C-0110-CP Jumper Plug to the Machine Control Assembly.
  2. Connect the C-0110-TOP Machine Start Harness to the Machine Control Assembly at H5.
    1. The opposite end of this harness connects directly to the FasCard reader.
Panel

Step 5 - Connect and Mount FasCard Reader

Bw part list
PartsC-6250,C-0110-TOP,C-5401,C-6205
SizingModeHeight
ShowDesc2false
ShowDesc3false
SingleRowtrue

  1. Feed remaining harness ends through mounting hole as described in F2 FasCard Reader Mounting Guide.
  2. Connect the free end of the C-0110-TOP Machine Start Harness to port 5 (Serial Connection Port) as shown in the image below.
  3. Connect the free end of the C-6250 Coin Sense Harness to port 3 (Coin 1 Connection Port) as shown in the image below.
  4. Connect the free end of the C-6205 Power Adapter Harness to port 1 (Power Connection Port) as shown in the image below.
  5. Connect FasCard reader to base as described in the F2 FasCard Reader Mounting Guide.
  6. Program the card reader address as described here: How to Program Address on a FasCard Reader.

Multiexcerpt include
MultiExcerptNameF2 Reader Ports
PageWithExcerptCCIDOC:_FC Reader Installation

Div
HidePrinttrue

Associated Equipment Models

Cci kits
TypeModels

Multiexcerpt include
MultiExcerptNameAdditional Info
DisableCachingtrue
PageWithExcerptCCIDOC:_FC Reader Installation