Page tree

Versions Compared

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.
Div
Classtoc-header
Section
Column
width30
Panel
titleOn this Page

Table of Contents
maxLevel2
minLevel2

Column
width70
Panel
titleOverview and Equipment Information

Multiexcerpt include
MultiExcerptNameOverview
PageWithExcerptCCIDOC:_FC Reader Installation

Kit Installation Notes

Cci kits
TypeDescription

Multiexcerpt include
MultiExcerptNameF2 Install Header
DisableCachingtrue
PageWithExcerptCCIDOC:_FC Reader Installation

Installation Kit

Cci kits
TypeParts

Recommended Tools and Supplies (Not Included)

See FasCard F1 Reader Mounting Guide for more information.

Installation

Multiexcerpt include
MultiExcerptNamewarnings
DisableCachingtrue
PageWithExcerptCCIDOC:_LC Reader Installation

Div
Classinstall-steps
Panel

Step 1 - Install Mounting Bracket

Bw part list
PartsC-6700-Temp,C-6801
SizingModeHeight
ShowDesc2false
ShowDesc3false
SingleRowtrue

  1. Place the C-6700-TEMP Drill Template on the desired mounting location.
  2. Verify included harnesses will reach desired location without encountering interference from internal machine components.
  3. Refer to FasCard Mounting Guide for further instructions.
Panel

Step 2 - Connect Power

Bw part list
PartsC-5203,C-5500,C-5602
SizingModeHeight
ShowDesc2false
ShowDesc3false
SingleRowtrue

  1. Tap power as described in the Fascard Reader Install - Universal Concepts document by connecting the C-5203 Power Adapter Harness to terminal strip or contacts L1 and L2.
    1. Connect the ground wire to a chassis screw.
    2. Connect the opposite end to the C-5602 Power Converter.
  2. Connect the C-5500 Power Extension Harness to the appropriate connector on the C-5602 Power Converter. The remaining cable end connects to the FasCard reader.
Panel

Step 3 - Connect Coin Sense Harness

Bw part list
PartsC-6255
SizingModeHeight
ShowDesc2false
ShowDesc3false
SingleRowtrue

  1. Disconnect the Coin Drop from the Machine Control Assembly.
  2. Connect the C-6255 Coin Sense Harness to the harness connected to the Coin Drop.
Panel

Step 4 - Connect Machine Start Harness

Bw part list
PartsC-5264
SizingModeHeight
ShowDesc2false
ShowDesc3false
SingleRowtrue

  1. Connect the C-5264 Machine Start Harness to the Coin Counting Board Harness where the coin drop was previously connected.
  2. The remaining tap connections should be inserted between the coin block solenoid and the existing harness connected to the solenoid.
    1. Disconnect the existing harness and match the male/female connectors on that side and the solenoid side of the circuit. 
Panel

Step 5 - Connect and Mount FasCard Reader

Bw part list
PartsC-5500,C-62645264,C-52556255
SizingModeHeight
ShowDesc2false
ShowDesc3false
SingleRowtrue

Multiexcerpt include
MultiExcerptNameF2 Reader Ports
PageWithExcerptCCIDOC:_FC Reader Installation

  1. Feed remaining harness ends through mounting hole as described in FasCard F1 Reader Mounting Guide.
  2. Connect the free end of the C-5264 Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.
  3. Connect the free end of the C-6255 Coin Sense Harness to port 3 (Coin Sense Harness Connection Port) as shown in the image above.
  4. Connect the free end of the C-5500 Power Extension Harness to port 4 (C-5500 Power Harness Connection Port) as shown in the image above.
  5. Connect FasCard reader to base as described in the FasCard Mounting Guide.
  6. Program the card reader address as described here: How to Program Address on a FasCard Reader.
Div
HidePrinttrue

Associated Equipment Models

Cci kits
TypeModels

Multiexcerpt include
MultiExcerptNameAdditional Info
DisableCachingtrue
PageWithExcerptCCIDOC:_FC Reader Installation