Page tree

Versions Compared

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.
Div
Classtoc-header
Section
Column
width30
Panel
titleOn this Page

Table of Contents
maxLevel2
minLevel2

Column
width70
Panel
titleOverview and Equipment Information

Multiexcerpt include
MultiExcerptNameOverview
PageWithExcerptCCIDOC:_FC Reader Installation

Kit Installation Notes

Cci kits
TypeDescription

Multiexcerpt include
MultiExcerptNameF2 Install Header
DisableCachingtrue
PageWithExcerptCCIDOC:_FC Reader Installation

Installation Kit

Cci kits
TypeParts

Recommended Tools and Supplies (Not Included)

See F2 FasCard Mounting Guide for more information.

Installation

Multiexcerpt include
MultiExcerptNamewarnings
DisableCachingtrue
PageWithExcerptCCIDOC:_LC Reader Installation

Div
Classinstall-steps
Panel

Step 1 - Install Mounting Bracket

Bw part list
PartsC-6920r1,C-1059,C-6801
SizingModeHeight
ShowDesc2false
ShowDesc3false
SingleRowtrue

  1. Remove the existing Coin Drop.
    1. Refer to manufacturer documentation as needed.
  2. Insert the C-6920R1 Mounting Bracket into the Coin Vault and secure using the C-1059 Kep Nuts.
  3. Secure the C-5414 F2 Mounting Bracket to the C-6920R1 Mounting Bracket using the C-5702 Chase Nipple and C-5703 Nut.
Panel

Step 2 - Connect Machine Start Harness

Bw part list
PartsC-5380
SizingModeHeight
ShowDesc2false
ShowDesc3false
SingleRowtrue

  1. Disconnect the Coin Drop from the Machine Control Assembly.
  2. Connect C-5380 Combination Harness to the machine where the Coin Drop was previously connected.
    1. The 6 pin 2x3 female connector will not be connected to anything as the Coin Drop will not be used.
Panel

Step 3 - Connect Power

Bw part list
PartsC-5101,C-5210,C-5602,C-5500
SizingModeHeight
ShowDesc2false
ShowDesc3false
SingleRowtrue

  1. Tap power as described in the Fascard Reader Install - Universal Concepts document using the C-5101 Spade Taps provided.
  2. Connect the C-5210 Power Adapter Harness to the installed spade taps. Connect the opposite end to the C-5602 Power Converter.
  3. Connect the C-5500 Power Extension Harness to the appropriate connector on the C-5602 Power Converter. The remaining cable end connects to the FasCard reader.
Panel

Step 5 - Final Connections

Bw part list
PartsC-5380,C-5500
SizingModeHeight
ShowDesc2false
ShowDesc3false
SingleRowtrue

Multiexcerpt include
MultiExcerptNameF2 Install HeaderDisableCachingtrueReader Ports
PageWithExcerptCCIDOC:_FC Reader Installation

  1. Feed remaining harness ends through mounting bracket.
  2. Connect the free end of the C-5380 Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.
  3. Connect the free end of the C-5500 Power Extension Harness to port 1 (C-5500 Power Harness Connection Port) as shown in the image above.
  4. The small, black 5 pin connector will not be connected as the Coin Drop is not being used.
  5. Connect FasCard reader to base as described in the F2 FasCard Mounting Guide.
  6. Program the card reader address as described here: How to Program Address on a FasCard Reader.


Multiexcerpt include
MultiExcerptNameAdditional Info
DisableCachingtrue
PageWithExcerptCCIDOC:_FC Reader Installation