Page tree

Versions Compared

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.
Div
Classtoc-header
Section
Column
width30
Panel
titleOn this Page

Table of Contents
maxLevel2
minLevel2

Column
width70
Panel
titleOverview and Equipment Information

Multiexcerpt include
MultiExcerptNameOverview
PageWithExcerptCCIDOC:_FC Reader Installation

Kit Installation Notes

Cci kits
TypeDescription

Multiexcerpt include
MultiExcerptNameF2 Install Header
DisableCachingtrue
PageWithExcerptCCIDOC:_FC Reader Installation

Installation Kit

Cci kits
TypeParts

Recommended Tools and Supplies (Not Included)

See F2 FasCard Reader Mounting Guide for more information.

Installation

Multiexcerpt include
MultiExcerptNamewarnings
DisableCachingtrue
PageWithExcerptCCIDOC:_LC Reader Installation

Div
Classinstall-steps
Panel

Step 1 - Install Mounting Bracket

Bw part list
PartsC-6936,C-6801,C-0144
SizingModeHeight
ShowDesc2false
ShowDesc3false
SingleRowtrue

  1. Run the C-6205 Power Adapter Harness and the C-0110-TOP 5240 Machine Start Harness through the circular opening on the C-6936 Vault Mount Bracket.
  2. Spread the bracket wings to lock it into place once installed.
  3. Insert the C-6936 Vault Mount Bracket into the Coin Vault
  4. Run the C-6205 Power Adapter Harness and the C-0110-TOP 5240 Machine Start Harness through the circular opening on the C-5414 F2 Mounting Bracket.
  5. Use the C-0144 screws, attach the C-5414 F2 Mounting Bracket to the C-6936 Vault Mount Bracket.
Panel

Step 2 - Connect Power

Bw part list
PartsC-6204
SizingModeHeight
ShowDesc2false
ShowDesc3false
SingleRowtrue

  1. Connect the C-6204 12VDC Power Harness to the H10 Connection on the Machine Control Assembly.
    1. Connect the green wire to a chassis ground.
  2. The remaining end (3-pin molex) connects directly to the rear of the F2 FasCard Reader.
Panel

Step 3 - Connect Machine Start Harness

Bw part list
PartsC-5240,C-5365
SizingModeHeight
ShowDesc2false
ShowDesc3false
SingleRowtrue

  1. Connect the C-5240 Machine Start Harness to the Machine Control Assembly at H3.
    1. The opposite end of this harness connects directly to the FasCard reader.
  2. Connect the C-5365 Bypass Harness to the appropriate connections to bypass the Coin Vault Switch.
Panel

Step 4 - Connect and Mount FasCard Reader

Bw part list
PartsC-5240,C-6204
SizingModeHeight
ShowDesc2false
ShowDesc3false
SingleRowtrue

Multiexcerpt include
MultiExcerptNameF2 Reader Ports
PageWithExcerptCCIDOC:_FC Reader Installation

  1. Feed remaining harness ends through mounting hole as described in F2 FasCard Reader Mounting Guide.
  2. Connect the free end of the C-5240 Machine Start Harness to port 5 (Serial Connection Port) as shown in the image above.
  3. Connect the free end of the C-6205 Power Adapter Harness to port 1 (Power Connection Port) as shown in the image above.
  4. Connect FasCard reader to base as described in the F2 FasCard Reader Mounting Guide.
  5. Program the card reader address as described here: How to Program Address on a FasCard Reader.
Div
HidePrinttrue

Associated Equipment Models

Cci kits
TypeModels

Multiexcerpt include
MultiExcerptNameAdditional Info
DisableCachingtrue
PageWithExcerptCCIDOC:_FC Reader Installation