Page tree

Versions Compared

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.
Comment: Automatic update to correct links
Div
Classtoc-header
Section
Column
width30
Panel
titleOn this Page

Table of Contents
maxLevel2
minLevel2

Column
width70
Panel
titleOverview and Equipment Information

Multiexcerpt include
MultiExcerptNameOverview
PageWithExcerptCCIDOC:_FC Reader Installation

Kit Installation Notes

Cci kits
TypeDescription

Multiexcerpt include
MultiExcerptNameACA Dip Switches
PageWithExcerptCCIDOC:_FC Reader Installation

Multiexcerpt include
MultiExcerptNameInstall Header
DisableCachingtrue
PageWithExcerptCCIDOC:_FC Reader Installation

Installation Kit

Cci kits
TypeParts

Recommended Tools and Supplies (Not Included)

See FasCard F1 Reader Mounting Guide for more information.

Installation

Multiexcerpt include
MultiExcerptNamewarnings
DisableCachingtrue
PageWithExcerptCCIDOC:_LC Reader Installation

Div
Classinstall-steps
Panel

Step 1 - Install Mounting Bracket

Bw part list
PartsC-5762,C-5760-A,C-1059,C-1070-W
SizingModeHeight
ShowDesc2false
ShowDesc3false
SingleRowtrue

  1. Remove any existing Coin Drop and Coin Box.
  2. Install the C-5760-A Adapter Bracket onto the C-5762 Metercase Bracket.
  3. Install the C-5762 Metercase Bracket over the front of the Metercase and secure with C-1070-W Washer and C-1059 Nut.
  4. Refer to FasCard Mounting Guide for further information as needed.
Panel

Step 2 - Connect Power

Bw part list
PartsC-6204-40
SizingModeHeight
ShowDesc2false
ShowDesc3false
SingleRowtrue

  1. Connect the C-6204-40 12VDC Power Harness to the H10 Connection on the Machine Control Assembly.
    1. Connect the green wire to a chassis ground.
  2. The remaining end (3-pin molex) connects directly to the rear of the F2 FasCard Reader.
Panel

Step 3 - Connect Machine Start Harness

Bw part list
PartsC-5240
SizingModeHeight
ShowDesc2false
ShowDesc3false
SingleRowtrue

  1. Connect the C-5240 Machine Start Harness to the H3 connection on the Machine Control Assembly serial port.
Panel

Step 4 - Connect and Mount FasCard Reader

Bw part list
PartsC-5240,C-6204
SizingModeHeight
ShowDesc2false
ShowDesc3false
SingleRowtrue

Multiexcerpt include
MultiExcerptNameReader ports
PageWithExcerptCCIDOC:_FC Reader Installation

  1. Feed remaining harness ends through mounting hole as described in FasCard F1 Reader Mounting Guide.
  2. Connect the free end of the C-5240 Machine Start Harness to port 1 (Serial Connection Port) as shown in the image above.
  3. Connect the free end of the C-6204 Power Extension Harness to port 4 (C-5500 Power Harness Connection Port) as shown in the image above.
  4. Connect FasCard reader to base as described in the FasCard Mounting Guide.
  5. Program the card reader address as described here: How to Program Address on a FasCard Reader.
Div
HidePrinttrue

Associated Equipment Models

Cci kits
TypeModels

Multiexcerpt include
MultiExcerptNameAdditional Info
DisableCachingtrue
PageWithExcerptCCIDOC:_FC Reader Installation