Page tree

Versions Compared

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.
Section
Column
width30
Panel
borderColorgrey
titleColor#FFFFFF
borderWidth1
titleBGColorgrey
titleTable of Contents
Table of Contents
maxLevel2
minLevel2
excludeTable of Contents
Column
width70
Panel
borderColorgrey
titleColor#FFFFFF
borderWidth1
titleBGColorgrey
titleOverview and Equipment Information

Multiexcerpt include
MultiExcerptNameOverview
DisableCachingtrue
PageWithExcerptCCIDOC:_FC Reader Installation

Kit Installation Notes

Cci kits
TypeDescription

Multiexcerpt include
MultiExcerptNameInstall Header
PageWithExcerptCCIDOC:_FC Reader Installation

Install Kit (K-5704-CO)

Cci kits
TypeParts

Recommended Tools and Supplies

See FasCard F1 Reader Mounting Guide for more information. 


Installation

Multiexcerpt include
MultiExcerptNamewarnings
DisableCachingtrue
PageWithExcerptCCIDOC:_LC Reader Installation

Div
Classinstall-steps
IDK-5704-CO
Panel

Step 1 - Install Mounting Bracket

Bw part list
PartsC-5700-TEMP,C-5800
SizingModeHeight
ShowDesc2false
ShowDesc3false
SingleRowtrue

  1. Place the C-5700-TEMP Drill Template on the desired mounting location.
    1. Front Mount over card reader slot recommended.
    2. Alternative top mount can be used, recommend obtaining C-5633-R1 Label to cover card slot.
  2. Verify included harnesses will reach desired location without encountering interference from internal machine components.
  3. Refer to 
FasCard
  1. F1 Reader Mounting Guide for further instructions.
Panel

Step 2 - Connect Power

Bw part list
PartsC-

0122

5101,C-5210,C-5602,C-5500
SizingModeHeight
ShowDesc2false
ShowDesc3false
SingleRowtrue

  1. Tap power as described in the Fascard Reader Install - Universal Concepts document using the C-
0122 
  1. 5101 Spade Taps provided.
  2. Connect the C-5210 Power Adapter Harness to the installed spade taps. Connect the opposite end to the C-5602 Power Converter.
  3. Connect the C-5500 Power Extension Harness to the appropriate connector on the C-5602 Power Converter. The remaining cable end connects to the FasCard reader.
Panel

Step 3 - Connect Machine Start Harness

Bw part list
PartsC-0110-CP,C-0110-TOP
SizingModeHeight
ShowDesc2false
ShowDesc3false
SingleRowtrue

  1. Remove the existing Alliance Jumper Plug at H8 and connect the C-0110-CP Jumper Plug to the Machine Control Assembly.
  2. Connect the C-0110-TOP Machine Start Harness to the Machine Control Assembly at H5.
    1. The opposite end of this harness connects directly to the FasCard reader.
Panel

Step 4 - Connect and Mount FasCard Reader

Bw part list
PartsC-5500,C-0110-TOP
SizingModeHeight
ShowDesc2false
ShowDesc3false
SingleRowtrue

Multiexcerpt include
MultiExcerptNameReader ports
PageWithExcerptCCIDOC:_FC Reader Installation

  1. Feed harness ends through mounting hole as described in the FasCard Mounting Guide.
  2. Connect the C-0110-TOP Machine Start Harness to port 1 (Serial Communication Port) as shown above.
  3. Connect the C-5500 Power Extension Harness to port 4 (C-5500 Power Harness Connection Port) as shown above.
  4. Connect FasCard reader to base as described in the 
FasCard
  1. F1 Reader Mounting Guide.
  2. Program the card reader address as described here: How to Program Address on a FasCard Reader.

Associated Equipment Models

Cci kits
TypeModels
 


Multiexcerpt include
MultiExcerptNameAdditional Info
PageWithExcerptCCIDOC:_FC Reader Installation

 

...