Page tree

Versions Compared

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.
Div
Classtoc-header
Section
Column
width30
Panel
titleOn this Page

Table of Contents
maxLevel2
minLevel2

Column
width70
Panel
titleOverview and Equipment Information

Multiexcerpt include
MultiExcerptNameOverview
PageWithExcerptCCIDOC:_FC Reader Installation

Kit Installation Notes

Cci kits
TypeDescription

Multiexcerpt include
MultiExcerptNameInstall Header
DisableCachingtrue
PageWithExcerptCCIDOC:_FC Reader Installation

Installation Kit

Cci kits
TypeParts

Recommended Tools and Supplies (Not Included)

See FasCard F1 Reader Mounting Guide for more information.

Installation

Multiexcerpt include
MultiExcerptNamewarnings
DisableCachingtrue
PageWithExcerptCCIDOC:_LC Reader Installation

Div
Classinstall-steps
Panel

Step 1 - Install Mounting Bracket

Bw part list
PartsC-5700-Temp,C-5800
SizingModeHeight
ShowDesc2false
ShowDesc3false
SingleRowtrue

  1. Place the C-5700-TEMP Drill Template on the desired mounting location.
  2. Verify included harnesses will reach desired location without encountering interference from internal machine components.
  3. Refer to FasCard Mounting Guide for further instructions.
Panel

Step 2 - Connect Power

Bw part list
PartsC-

0122

5101,C-5210,C-5500,C-5602
SizingModeHeight
ShowDesc2false
ShowDesc3false
SingleRowtrue

  1. Tap power as described in the Fascard Reader Install - Universal Concepts document using the C-
0122 
  1. 5101 Spade Taps provided.
  2. Connect the C-5210 Power Adapter Harness to the installed spade taps. Connect the opposite end to the C-5602 Power Converter.
  3. Connect the C-5500 Power Extension Harness to the appropriate connector on the C-5602 Power Converter. The remaining cable end connects to the FasCard reader.
Panel

Step 3 - Connect Combination Coin Sense/Machine State Harness

Bw part list
PartsC-5335
SizingModeHeight
ShowDesc2false
ShowDesc3false
SingleRowtrue

  1. Disconnect the Coin Drop from the Machine Control Assembly.
  2. Connect the C-5335 Combination Harness (black connector) to the Coin Eye Sensor.
    1. The White wire (female) spade connectors bundled with the black connector attach to the Coin Block solenoid.
  3. Connect the Violet wire (male) spade connectors to the Coin Sense Input.
  4. Connect the remaining White wire (male) spade connectors to the Coin Block solenoid drive.
Panel

Step 4 - Connect and Mount FasCard Reader

Bw part list
PartsC-5335,C-5500
SizingModeHeight
ShowDesc2false
ShowDesc3false
SingleRowtrue

Multiexcerpt include
MultiExcerptNameReader ports
PageWithExcerptCCIDOC:_FC Reader Installation

  1. Feed remaining harness ends through mounting hole as described in
FasCard
  1. F1 Reader Mounting Guide.
  2. Connect the white connector on the C-5335 Combination Harness to port 2 (Pulse Connection Port) as shown in the image above.
  3. Connect the black connector on the C-5335 Combination Harness to port 3 (Coin Sense Harness Connection Port) as shown in the image above.
  4. Connect the free end of the C-5500 Power Extension Harness to port 4 (C-5500 Power Harness Connection Port) as shown in the image above.
  5. Connect FasCard reader to base as described in the FasCard Mounting Guide.
  6. Program the card reader address as described here: How to Program Address on a FasCard Reader.
Div
HidePrinttrue

Associated Equipment Models

Cci kits
TypeModels

Multiexcerpt include
MultiExcerptNameAdditional Info
DisableCachingtrue
PageWithExcerptCCIDOC:_FC Reader Installation